Bosch MSI 60 Скачать руководство пользователя страница 112

Страница: 112 / 120

15 | GPS Sensor

112 / 120

Modular Sensor Interface MSI 60

Bosch Motorsport

15.4 Measurement Labels

The decoded NMEA messages are copied to these MSI 60 measurement labels.

Measurement label

Function

gps_PDOP

Position Dilution Of Precision

gps_HDOP

Horizontal Dilution Of Precision

gps_VDOP

Vertical Dilution Of Precision

gps_lat

Latitude in NDEG - +/-[degree][min].

[sec/60]

gps_long

Longitude in NDEG - +/-[degree][min].

[sec/60]

gps_elv

Antenna altitude above/below mean sea

level (geoid) in meters

gps_speed

Speed over the ground in kilometers/hour

gps_direction

Track angle in degrees

gps_declination

Magnetic variation degrees (Easterly var.

subtracts from true course)

gps_year

Years since 1900

gps_mon

Months since January - [0,11]

gps_day

Day of the month - [1,31]

gps_hour

Hours since midnight - [0,23]

gps_min

Minutes after the hour - [0,59]

gps_sec

Seconds after the minute - [0,59]

gps_hsec

Hundredth part of second - [0,99]

gps_smask

Mask specifying types of packages from

which data has been obtained

gps_sig

GPS quality indicator (0 = Invalid; 1 = Fix; 2

= Differential, 3 = Sensitive)

gps_fix

Operating mode, used for navigation (1 =

Fix not available; 2 = 2D; 3 = 3D)

These measurement labels are arrays, where the indexed element points to the same

satellite (E.g. gps_info_satsigstrength[3] tells the receiving signal strength of satellite 3.

Satellite 3 has the SAT-ID given in gps_info_satid[3]).

Measurement label

Function

gps_info_satid[ ]

Satellite PRN number

gps_info_satinuse[ ]

Used in position fix

gps_info_satelevation[ ]

Elevation in degrees, 90 maximum

gps_info_satazimuth[ ]

Azimuth, degrees from true north, 000 to

359

gps_info_satsigstrength[ ]

Signal, 00-99 dB

Содержание MSI 60

























































































































Результаты поиска

Содержание MSI 60

Отзывы:

Бренды по названию

Популярные бренды

Bosch MSI 60, Руководство пользователя

Результаты поиска

Содержание MSI 60

Отзывы:

Бренды по названию

Популярные бренды