Bosch IRIS-Net, Руководство пользователя

Страница: 11 / 994

and place them as desired. To select and place bitmaps and text boxes, follow the same procedure accordingly
(Add Bitmap..., Add Textbox...). In case you need several similar control groups, start with creating one group.
Once you are finished with that particular group, select the entire group by dragging a highlight box around it and
Copy/Paste it. Alternatively you can save the complete group as a User Control (Save User Control menu
command) and reuse the User Control in various other projects.
10. Programming User Control Panels. Control elements of control panels can be used to control or to indicate various
power amp parameters. A click with the right mouse button onto the control element opens the corresponding
configuration dialog. Choose Administrate Connections and select the desired connection for the control element
(power amps, groups, other control elements) from the connections list. Select Modify Properties for setting/
modifying the control element’s properties. Click in the line on the right next to function and select one or several
parameters to be controlled from the parameter listing. If needed, set additional control element properties
accordingly. Afterwards, make sure to test the control element’s functions.
11. Programming Power Amplifier Parameters. A double click on a power amplifier icon opens the Amplifier Control
Panel. The Amplifier Control Panel allows naming power amps and channels, switching power amps on / off,
setting level controls and mutes, and assigning and monitoring input or output signals to the monitor bus. Click on
the SET button to open the Setup & Control Window. This window includes five different pages: Config & Info,
DSP, Speaker, Load, Supervision & Test. "Config & Info" provides information about power amplifier type,
firmware revision and configuration. In addition you are able to program the power-on delay, enter power amp and
channel names, and specify functions of the GPIO port. Furthermore, programming job functions (control
functions, which are sent and received via the CAN-network) is also possible. "DSP" allows setting all DSP
parameters and saving them in presets. Recalling presets, import (read from file) and export (save to file) is
possible as well. The DSP parameters include Master EQ, Master Delay, Routing, Channel EQ, X-Over with Level
Trim and Alignment Delay as well as Dynamic functions including compressors and limiters. On the "Speaker" page
you are able to select loudspeaker files with measured frequency and phase responses and assign them to
individual power amplifier channels. This response plots can be displayed in EQ and X-Over windows to allow
optimized parameter settings. "Load" provides information about measured output voltages and currents and the
resulting calculated load. You can set the limits for the allowable impedance range and start impedance tests of a
defined frequency range. Impedance graphs can be saved as reference measurements with tolerance spread.
"Supervision & Test" provides indication of different fault types. You are able to select which failures result in a
fault messages. Activating the pilot tone function is also performed on this page. Also provided is a test tone
generator for manual testing.
12. Password Protection. Each page (layer) can be protected by an individual password. Programming different
access rights is possible as well. Open the password dialog in the Menu Configuration, Passwords.... Enter a
password for the system administrator (probably you) and add new users (New User) if needed. You have to enter
the user names, passwords and access rights. Specifying at least an administrator password and protecting the
configuration page against unwanted access is generally recommended.
Configuration Of A Remote Power Amplifier System Using a NetMax N8000 System Controller
1.
Start The IRIS-Net Software. IRIS-Net starts creating a new project and opens an empty "Configuration Page"
worksheet.
2. Saving. Name your new project before saving (File Save). Creating a separate folder for each project in the
directory \IRIS-Net\Projects\ is strongly recommended. All files associated with a specific project (e.g. bitmaps)
need to be located within that particular folder. Periodically saving the project is generally good advice.
3. Creating N8000 System Controller. Clicking the right mouse button within the Worksheet opens a Configuration
Dialog. Click on Add Devices... using the left mouse button, drag a N8000 out of the device list and drop them in
the worksheet area. Specify the number of devices to be created. The devices appear together with a PC-icon on
the computer screen when hitting OK. The symbol of the PC represents the control-PC and the NCP-interface.
IRIS-Net IRIS-Net | en 11
Bosch Security Systems B.V. User Manual 2017.05 | 3.20 | F.01U.119.956