Belarus 3522.5 Скачать руководство пользователя | Manualshive

Страница: 262 / 340

background image

3522.5-0000010 OM

263

б

) during operation of tires on doubled wheels:

(considering a permissible load on a tire during operation of tires on doubled wheels):

1.7

f

G

doubl.

=

f

G

1.7

Z

G

doubl.

=

Z

G

f

G

doubl.

=

7

,

1

f

G

Z

G

doubl.

=

7

,

1

Z

G

where

f

G

doubl.

and

Z

G

doubl.

are calculated loads for pressurization of tires during

operation of tires on doubled wheels.

Further according to the calculated loads from Table 4.3 of loading instructions, tire

pressure shall be determined (subsection 4.2.9 “Selection of tires internal pressure in de-
pending on operating conditions and load on the tractor axles, and tires operating rules”).

Tractor controllability criterion calculation:
- without water solution in the front tires

Т

f

is load on the tractor front axis,

Н

;

k

f

is tractor controllability criterion;

M is tractor operating weight (during calculation ballasts weights in the tractor oper-

ating weight

М

are not taken into account), kg;

ATTENTION: COUPLING OF THE IMPLEMENTS TO THE TRACTOR SHALL NOT

RESULT IN EXCESS OF PERMISSIBLE AXIS LOADING AND LOADS ON THE TRAC-
TOR TIRES!

ATTENTION: MINIMUM WEIGHT OF THE IMPLEMENTS COUPLED AND BAL-

LAST WEIGHTS USED SHALL ALWAYS MAKE NOT LESS THAN VALUES AT WHICH
LOAD ON THE FRONT TRACTOR WHEELS IN STRUCTURE OF MTU SHOULD AL-
WAYS MAKE NOT LESS THAN 20% OF THE TRACTOR OPERATING WEIGHT, AND
THE CONTROLABILITY CRETERION SHOULD MAKE NOT LESS THAN 0.2!

5.11 Possibility to install front loader

ATTENTION: INSTALLATION OF ANY MOUNTABLE EQUIPMENT ON THE

TRACTOR “BELARUS-3522.5” (INCLUDING MOUNTABLE FRONT LOADERS) WHICH
IN NOT RALATED TO MOUNTED, SEMIMOUNTED, SEMITRAILED OR TRAILED IM-
PLEMENTS, BY MEANS OF FASTENING OF SPESIAL-PUPOSE ASSENBLY UNITS
FROM THE MOUNTABLE EQUIPMENT KIT TO THE TRACTOR MOUNTING HOLES, IS
NOT PROVIDED!

https://tractormanualz.com/

«
...
260
261
262
263
264
...
»

Содержание 3522.5





















































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3522.5

Бренд: MacDon Страницы: 2

Бренд: Zetor Страницы: 197

Бренд: Iseki Страницы: 98

Бренд: Iseki Страницы: 176

Бренд: Yanmar Страницы: 16

Бренд: Troy-Bilt Страницы: 113

Бренд: Hagie Страницы: 67

Бренд: Kioti Страницы: 108

Бренд: Sears Страницы: 19

Бренд: Sears Страницы: 36

Бренд: Itouchless Страницы: 6

Бренд: GRADEN Страницы: 26

Бренд: GRADEN Страницы: 24

Бренд: AGRI-COVER Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды