manualshive.com logo in svg

Belarus 3522.5, Руководство оператора

Оператор состав мануал для Belarus 3522.5 доступен для скачивания совершенно бесплатно на manualshive.com. Этот руководство содержит важную информацию о производственном оборудовании, которая поможет вам эффективно использовать ваш трактор. Скачайте ваш экземпляр сейчас, чтобы быть в курсе всех функций и возможностей Belarus 3522.5.

Поделиться
Скачать
background image

3522.5-0000010 OM

309

7. Failures that may possibly emerge in the electrical facilities, hy-

draulic lift linkage and guidelines for troubleshooting

7.1 Possible failures in the electronic system for gearbox, rear axle differential

lock, front driving axle drive, front and rear power take off shaft control, and
guidelines for troubleshooting

List of possible failures in the electronic system for gearbox, rear axle differential

lock, front driving axle drive, front and rear power take off shaft control, and guidelines for
troubleshooting are shown in Table 7.1.

Table 7.1

Failure,

 external manifestations, cause

Troubleshooting

One of the drives (RA DL, FDA, FPTO, RPTO) or a gear can not be engaged, or be-

comes disengaged after engagement
Short circuit in control valve solenoid
of a drive or a gear that is displayed
by   single flash of the corresponding
power-on indicator (actuated by the
pressure sensor at the control valve
output)

- check the electric circuit for normal operation from
CECS to the respective control valve solenoid accord-
ing to the diagram (Annex C). In case a

failure

 is de-

tected eliminate it.
- test the coil resistance of the respective control valve
solenoid, it shall be within the range from 4 to 6
Ohm. If the coil resistance is close to 0 Ohm, replace
the solenoid

Open circuit in the control valve sole-
noid  of a drive or a gear – that is dis-
played by two-times flash of the cor-
responding power-on indicator (actu-
ated by the pressure sensor at the
control valve output)

- check the electric circuit for normal operation from
CECS to the respective control valve solenoid accord-
ing to the diagram (Annex C). In case a

failure

 is de-

tected eliminate it.
- test the coil resistance of the respective control valve
solenoid, it shall be within the range from 4 to 6
Ohm. If the coil resistance is close to infinite distance,
replace the solenoid

One of the drives (RA DL, FDA, FPTO, RPTO) or a gear can be engaged only for a

very short period (from 1 to 6 sec), or becomes disengaged after engagement

If the pressure in the transmission hydraulic system is
below the standard (pressure in the transmission hy-
draulic system shall make from 1.3 to 1.5 MPa), elimi-
nate the failure

Pressure sensor, installed at a control
valve output of a drive or a gear, does
not respond. The failure is displayed
by three-times flash of the corre-
sponding power-on indicator

If the transmission hydraulic system is under a standard
pressure, remove the cable socket with the sensor
pressure and insert the bonding strip to simulate the
sensor response:
- if the error code indicator (three-times flash) is still
blinking, it is necessary to check the circuit to the pres-
sure sensor according to the diagram;
- if the error code indicator went out, the pressure sen-
sor shall be replaced by a new properly operating one

https://tractormanualz.com/

Содержание 3522.5





















































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3522.5

Mahindra 2810 Service Manual preview
2810
Бренд: Mahindra Страницы: 223
Bad Boy 1025H Operator'S Manual preview
1025H
Бренд: Bad Boy Страницы: 144
Homelite LM-991013 Instructions-Parts List preview
LM-991013
Бренд: Homelite Страницы: 2
Mitsubishi Mahindra GX3600 Service Manual preview
Mahindra GX3600
Бренд: Mitsubishi Страницы: 106
Daedong KIOTI UD28-A901AF Installation Instructions Manual preview
KIOTI UD28-A901AF
Бренд: Daedong Страницы: 11
Kubota STV32 Operator'S Manual preview
STV32
Бренд: Kubota Страницы: 102
Kubota MX5200 Operator'S Manual preview
MX5200
Бренд: Kubota Страницы: 115
Iseki TA525F Operation Manual preview
TA525F
Бренд: Iseki Страницы: 51
New Holland TT4.80 Service Manual preview
TT4.80
Бренд: New Holland Страницы: 41
Broan Elite 15XESSEXF Service Manual preview
Elite 15XESSEXF
Бренд: Broan Страницы: 39
Kellfri 37-27070SHCC Instruction Manual preview
37-27070SHCC
Бренд: Kellfri Страницы: 16
EarthBin Silo EB500 User Manual preview
Silo EB500
Бренд: EarthBin Страницы: 22
GE UCG1520NSS Installation Instructions Manual preview
UCG1520NSS
Бренд: GE Страницы: 16
Kioti KL155 Manual preview
KL155
Бренд: Kioti Страницы: 108
SUMMIT EQUIPMENT S-V95 Maintenance Manual preview
S-V95
Бренд: SUMMIT EQUIPMENT Страницы: 30
SUMMIT EQUIPMENT SC-3248 Safety, Operation & Maintenance Manual preview
SC-3248
Бренд: SUMMIT EQUIPMENT Страницы: 35
Frontier BB3272 Operator'S Manual preview
BB3272
Бренд: Frontier Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды