manualshive.com logo in svg

Belarus 3522.5, Руководство оператора

Оператор состав мануал для Belarus 3522.5 доступен для скачивания совершенно бесплатно на manualshive.com. Этот руководство содержит важную информацию о производственном оборудовании, которая поможет вам эффективно использовать ваш трактор. Скачайте ваш экземпляр сейчас, чтобы быть в курсе всех функций и возможностей Belarus 3522.5.

Поделиться
Скачать
background image

3522.5-0000010 OM

232

4.3 Safety measures when operating the tractor

4.3.1 General safety measures when operating the tractor
Do not operate the tractor in a closed room without required ventilation. Exhaust

gas may result in lethal outcome.

Tractor start-up and operation with hood lateral sides removed and mask opened is

not allowed.

It is forbidden to remove the hood lateral sides and (or) lift up the hood mask when

the engine is running.

Do not start the engine when staying outside the operator's seat. Starting the en-

gine and manipulating the controls, always stay inside the cab in the operator's seat.

Do not start the engine by way of towing.
Before starting the engine, engage the parking brake, the gear range shifting lever

shall be in “Neutral” position.

During tractor start there shall be no people under the tractor, in front of it or behind,

as well as between the tractor and the coupled implement.

Before stopping the engine set “0” gear with the gear shifting joystick.
Before setting on the move warn people around including those operating the cou-

pled implements using the horn, make sure the parking brake is off and start moving
slowly. Use safety harnesses (supplied against order) at hauling operations.

Passenger staying in the cab during tractor operation is strictly forbidden. (Passen-

ger may stay in the cab only when an additional seat is installed).

Do not leave the tractor on the move.
Performing hauling operations observe traffic requlations, adopted in your country.
Hauling operations may be carried out by operators with not less than two years of

tractor operation experience and those who have passed exams in traffic regulations.

Drive the tractor on slippery roads with ADL engaged only at a speed not higher

than 10 km/h.

Before using the tractor for hauling operations do the following:
- set a haulage track for rear wheels;
- check operation of brakes; interlock brake pedals, check and if necessary adjust

the brakes for simultaneity of operation;

- check operation of the parking brake;
- check a condition of devices for light and sound indication; hauling trailers shall

have rigid hitches and be linked with a safety chain or a cable;

- never move downhill with the gear disengaged. Move uphill and downhill at the

same gear;

It is forbidden to operate with a trailer without independent brakes, if its weight ex-

ceeds a half of a total actual weight of the tractor. The faster you move and the more
weight you tow, the bigger safety distance shall be.

It is forbidden to drive the tractor with twinned wheels on public roads!

Hauling people inside trailers is forbidden.

Before getting down to work with a trailer turn the compressor on, check the condi-

tion of the trailer brake pneumatic drive and air pressure in the system. Remove the fail-
ures detected. Make sure to connect the traler brake pneumatic drive. Carry out connec-
tion of the trailer connecting head to the tractor connecting head with the parking brake
engaged.

Trailers attached to the tractor shall have a braking system, ensuring
-  trailer brake on movement;
-  brake engagement in case of trailer detachment from the tractor;
-  holding the trailer when staying on slopes;
-  prevention of trailer from pushing the tractor when the travel speed is changed

abruptly.

https://tractormanualz.com/

Содержание 3522.5





















































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3522.5

FENDT FAVORIT 900 Workshop Manual preview
FAVORIT 900
Бренд: FENDT Страницы: 1245
Husqvarna LTH125 Instruction Manual preview
LTH125
Бренд: Husqvarna Страницы: 68
Husqvarna TS 343 Instruction Manual preview
TS 343
Бренд: Husqvarna Страницы: 104
Camoplast ATV T4S Manual preview
ATV T4S
Бренд: Camoplast Страницы: 16
Bolens G-14 Owner'S Manual preview
G-14
Бренд: Bolens Страницы: 19
Bolens DuraTrac 5117H Service Manual preview
DuraTrac 5117H
Бренд: Bolens Страницы: 104
FENDT 900 Vario Gen6 Series Workshop Service Manual preview
900 Vario Gen6 Series
Бренд: FENDT Страницы: 51
New Holland Boomer 1020/T1010 Specifications preview
Boomer 1020/T1010
Бренд: New Holland Страницы: 1
Trac Vac 858-RH Operating And Assembly Manual preview
858-RH
Бренд: Trac Vac Страницы: 9
PÖTTINGER EUROROFI Mounting Instructions preview
EUROROFI
Бренд: PÖTTINGER Страницы: 14
Pottinger SYNKRO 4003 K+T Operator'S Manual preview
SYNKRO 4003 K+T
Бренд: Pottinger Страницы: 31
Princeton PIGGY BACK PB50 Operator'S Manual preview
PIGGY BACK PB50
Бренд: Princeton Страницы: 28
Holder Tractor C992 Operating Manual preview
C992
Бренд: Holder Tractor Страницы: 129
GreenTec HXF Series Quick Start Manual preview
HXF Series
Бренд: GreenTec Страницы: 12
GreenTec 9991902C-25 Instruction Manual preview
9991902C-25
Бренд: GreenTec Страницы: 76
Cucine Oggi EKKO CUBE 40 9000 Assembly Instructions preview
EKKO CUBE 40 9000
Бренд: Cucine Oggi Страницы: 3
Cucine Oggi i.Master Double Assembly Instructions preview
i.Master Double
Бренд: Cucine Oggi Страницы: 5

Бренды по названию

Популярные бренды

Загрузить еще бренды