manualshive.com logo in svg

Belarus 3522.5, Руководство оператора

Оператор состав мануал для Belarus 3522.5 доступен для скачивания совершенно бесплатно на manualshive.com. Этот руководство содержит важную информацию о производственном оборудовании, которая поможет вам эффективно использовать ваш трактор. Скачайте ваш экземпляр сейчас, чтобы быть в курсе всех функций и возможностей Belarus 3522.5.

Поделиться
Скачать
background image

3522.5-0000010 

РЭ

225

4.2.9.2 Instructions for tire use
To prevent premature wear of tires and tractor breakdown due to wrong use of tires,

follow the below instructions for tire use:

- carry out operations in technical maintenance of tires and wheels;
- keep tires away from fuel, oil and other oil products;
- it not recommended to use pressure below 0,09 MPa. With tire pressure 0,08 MPa

and less (inner pressure reduction below a required value due to possible air leakage)
carry out a constant pressure control;

- data on loads for 10 km/h (in table 4.3) are used only in conditions, requiring low

traction force: when coupling seeder and harvesting units. For operations requiring large
turning torque (tillage, etc.) use instructions for speed of 30 km/h;

- do not operate the tractor with tire inner pressure not corresponding to a regulation

rate for each specific case of its use;

- keep to the established rates of tire inner pressure in accordance with the instruc-

tions of the present manual;

- when it is necessary to check and inflate tires during operation do not do it straight

after the tractor is stopped: time gap is required to let tires cool off;

- control air pressure in tires in cold condition with tire gage, which is to be periodi-

cally tested for precision of indications at stations or centers of cervice for any mechanical
vehicles;

- if air pressure drop is constantly observed in tires, be sure to find out the fault and

eliminate it;

- check pressure in tires, filled with a solution, with the valve staying in the extreme

upper position;

- when mounting twinned wheels on one axis inner pressure shall be provided in

accordance with the instructions of the table 4.3;

- use of tire sizes, not specified in the manual, is only possible upon agreement with

the plant;

- choosing and buying new tires follow the instructions of this manual.
Wrong mounting and dismounting of tires results in damage to elements of tire

structure. In household conditions tires are mounted and dismounted in a specially allo-
cated area or in a room. As a rule, tires are mounted/dismounted on a special stand, but
manual mounting/dismounting of tires is also possible (by means of tire levers and other
fixtures).

Mount tires of the same size, model and design on one axis. Periodical wheel rear-

rangement precludes their uneven wear. Do not mount wheels with various wear rates on
one axis;

- comply with a permitted axial load to reach max. pulling force in particular opera-

tional conditions during tillage and also to reach least soil compaction;

- when making a track it is obligatory to provide equal distance for counter wheels

with relation to a vertical plane, crossing the center of the tractor. Mounting wheels re-
member of a correct direction of tire rotation and of a safe distance between the wheel and
other elements of tractor design;

https://tractormanualz.com/

Содержание 3522.5





















































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3522.5

Jacobsen G-10 Operator'S Manual And Parts List preview
G-10
Бренд: Jacobsen Страницы: 54
New Holland T8.275 Service Manual preview
T8.275
Бренд: New Holland Страницы: 81
Cub Cadet 3208 Operator'S Manual preview
3208
Бренд: Cub Cadet Страницы: 48
Zetor 7520 Operator'S Manual preview
7520
Бренд: Zetor Страницы: 236
Zetor Proxima CL 80 Operator'S Manual preview
Proxima CL 80
Бренд: Zetor Страницы: 210
Mahindra MXSB-56 Owner'S Manual preview
MXSB-56
Бренд: Mahindra Страницы: 24
Jenn-Air TC507 Use & Care Manual preview
TC507
Бренд: Jenn-Air Страницы: 28
GE GCG1700P Dimensions And Installation Information preview
GCG1700P
Бренд: GE Страницы: 2
Electrolux 99526808A Use And Care Manual preview
99526808A
Бренд: Electrolux Страницы: 36
Electrolux E15TC75H Factory Parts Catalog preview
E15TC75H
Бренд: Electrolux Страницы: 4
Sears Craftsman 944.600940 Owner'S Manual preview
Craftsman 944.600940
Бренд: Sears Страницы: 60
Toro 71202 Operator'S Manual preview
71202
Бренд: Toro Страницы: 46
Hayter RS102H Spare Parts Manual preview
RS102H
Бренд: Hayter Страницы: 28
Hayter RT380H Operator'S Manual preview
RT380H
Бренд: Hayter Страницы: 52
DFM CFB16 Operator'S Manual preview
CFB16
Бренд: DFM Страницы: 20
DFM TurboSaw EX2600 Operator'S Manual preview
TurboSaw EX2600
Бренд: DFM Страницы: 28
AGCO FENDT 1000 Vario Operator'S Manual preview
FENDT 1000 Vario
Бренд: AGCO Страницы: 6
AGCO Massey Ferguson 533 Workshop Service Manual preview
Massey Ferguson 533
Бренд: AGCO Страницы: 31

Бренды по названию

Популярные бренды

Загрузить еще бренды