Belarus 3522.5 Скачать руководство пользователя | Manualshive

Страница: 331 / 340

background image

3522.5-0000010 OM

332

8.5 Preservation

Preservation provides provisional anticorrosion protection of tractor assemblies and

systems from ambient exposure in the process of tractor transportation and storage.

Engine. its systems and fuel tank preservation instructions are listed in the engine

operation manual.

Tires preservation is regulated by provisions of subsection 8.1 “General instruc-

tions”.

Clean tractor surfaces subject to preservation from mechanical staining, degreased

and dried up. Cover unpainted inside and outside galvanized surfaces, specific assemblies
of tractor and cabin with corrosion-proof oil RUST BAN 397, SUMIDERA 397.

Preservation of units (radiator and fuel tank filler, breathers, cylinder rods) is carried

out by polyethylene film.

Materials used provide protection of tractor and its assemblies for the period of

storage and transportation within one year.

Outside tractor and its assemblies preservation is made by lubrication of surfaces

using brush or sputtering by means of paint sprayer. Inside tractor preservation is carried
out by filling cavities with preservation mixture and subsequent engine operation.

During tractor inter-shift, short-term and long-term storage, the enterprise operating

the tractor is liable for compliance with preservation methods and storage conditions speci-
fied in GOST 7751-85. Inside tractor surfaces preservation is carried out by preservation
grease

КС-У

according to TU RB 600125053.019-2004. When a tractor is stored outside,

specific surfaces must be preserved with grease “BELA-COR» of type “

А

” according to TU

RB 600125053-020-2004.

8.6 Depreservation and represervation

Depreservation method is chosen depending on preservation materials used. Sur-

faces under preservation have to be wiped with cleaning cloth soaked with low-viscous
oils, solvents, or washed away with washing water-soluble detergents. Sealed assembles
should be stripped off insulation materials (film, paper). Inside surfaces under preservation
need no depreservation.

Tractor represervation is carried out in case conservation defects are detected in

the process of storage or upon expiration of protection life.

8.7 Putting tractor into operation after long-term storage

Perform depreservation of an engine according to the engine operation manual.
Remove grease off external surfaces under preservation. Dismount protective cov-

ers, plugs, special accessories and mount the parts which were removed earlier back in
their places. Before mounting parts clean them off grease and dust. Drain sediment out of
all vessels, fill them with operation fluids and, if necessary, top up to control level.

Lubricate all tractor mechanisms according to clause 3 of Table 6.3 of the present

operation manual. Carry out scheduled maintenance. Run tractor for 15-20 minutes. Cor-
rect detected faults if necessary.

https://tractormanualz.com/

«
...
329
330
331
332
333
...
»

Содержание 3522.5





















































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3522.5

Бренд: Zetor Страницы: 134

Бренд: MTD Страницы: 33

Workmaster 33 Tier 4B

Бренд: New Holland Страницы: 51

Бренд: Weir Страницы: 12

Бренд: Troy-Bilt Страницы: 113

Бренд: Valtra Страницы: 41

Бренд: FENDT Страницы: 51

Бренд: GE Страницы: 26

Бренд: Kverneland Страницы: 67

Бренд: MASSEY FERGUSON Страницы: 41

Бренд: Branson Страницы: 7

Бренд: Branson Страницы: 135

Бренд: Branson Страницы: 151

Бренд: Branson Страницы: 167

Бренд: Branson Страницы: 172

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды