Belarus 3522.5 Скачать руководство пользователя | Manualshive

Страница: 41 / 340

background image

3522.5-0000010

РЭ

42

Using the mode of choosing between inducible parameters the customer can acti-

vate, if necessary, displaying of various engine parameters on the screen as per table 2.5.
The mode of parameter choosing is activated after activation of the button panel with
short-time pressing the button 5. Sequential pressing the button 1 changes the parameters
displayed in the upper left corner, pressing the button 2 changes the parameters in the up-
per right corner, button 3 – in the lower left corner, button 4 – in the lower right corner. The
parameter choosing mode is exited with short-time pressing the button 5.

As the button panel has been activated pressing the button 3 activates graphical

displaying of parameters in the course of time (functions as parameter analogue recorder).

The required parameters are chosen with a sequential pressing the button 3 as per

table 2.5.

A temporary net can be adjusted in a configuration menu from 2, 10 or 30 min. to 1,

2, 4 or 8 hours. To enter the configuration menu it is necessary to press the button 5 for
more than 3 sec., after that enter PIN-code. After the PIN-code has been entered it is pos-
sible to choose metric and British units of measurement in this menu, among available
languages it is possible to choose English, Spanish, Swedish, French, German, Italian,
Dutch, Portuguese and Russian.

ATTENTION: ONLY DEALERS ARE AUTHORISED TO ENTER PIN-CODE AND

CHANGE SETTINGS OF CONFIGURATION MENU!

When errors (faults) are detected during operation the monitor produces a sound

signal and a rhombic flashing window with an exclamation mark appears on the screen.

After the button panel has been activated a list of active errors (faults) is invoked

with the button 4. Moving over the list is carried out with the button 1 and 2. The errors, the
reception of which has not yet been confirmed, are printed in grey buttons on a black
background.

To exit displaying of the lift of active errors it is necessary to confirm reception of all

errors by pressing the button 3. After that confirmation errors are printed in black buttons
on a grey background.

After the fault has been eliminated active errors pass automatically to the lift of inac-

tive errors.

The list of inactive errors is activated with pressing and holding the button 4. The

engine electronic control unit provides a possibility to delete the information on stored er-
rors, it is possible to erase them when they are on the screen, to do this it is required to
press and hold the button 3.

https://tractormanualz.com/

«
...
39
40
41
42
43
...
»

Содержание 3522.5





















































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3522.5

Бренд: SaMASZ Страницы: 29

Versu N2 Series

Бренд: Valtra Страницы: 31

MAGNATRAC MH8000

Бренд: Struck Страницы: 69

Бренд: Bolens Страницы: 19

Бренд: Bolens Страницы: 104

WILDKAT JD6105-20E T4F

Бренд: Tiger Страницы: 238

Бренд: WilTec Страницы: 5

Бренд: Toro Страницы: 2

Бренд: Toro Страницы: 4

Бренд: Toro Страницы: 4

Бренд: Toro Страницы: 4

Бренд: Toro Страницы: 20

Бренд: Toro Страницы: 20

08881 SAND PRO 5000

Бренд: Toro Страницы: 28

Бренд: Iran Tractor Страницы: 106

Бренд: Iran Tractor Страницы: 118

Бренд: Iran Tractor Страницы: 122

Бренд: Digga Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды