Belarus 3522.5 Скачать руководство пользователя | Manualshive

Страница: 59 / 340

background image

3522.5-0000010

РЭ

60

To turn off the “dampening” mode press the button 10. The annunciator of “dampen-

ing” deactivation will go out, and the RLL will return to its top position. Move the retainer 8
to its initial position.

ATTENTION: THE “DAMPENING” MODE IS ACTIVE ONLY THE HANDLE 7 IS IN

THE “UPLIFT” POSITION!

ATTENTION: DURING FIELD WORKS (TILLAGE, CULTIVATION) THE “DAMPEN-

ING” MODE SHALL BE TURNED OFF!

2.14.3 Remote buttons of RLL control system

Remote buttons of RLL control are used as a rule for coupling agricultural imple-

ments and machines to the rear lift linkage.

Uplift and lowering of the rear lift linkage with the remote buttons on rear wheel

fenders can be carried out at different control modes – the handles 1, 2, 3, 4, 7 (figure
2.14.1) can be left in any position, as the system of control from inside the cab is hereby
blocked.

To lift the RLL up, press any of the buttons 4 (figure 2.14.2) and hold it depressed.

To lower the RLL, press any of the buttons 3 and hold it depressed.

For safety's sake the control with the remote buttons is performed under interruption

of work. Pressing the uplift button 4 (lowering button 3) and holding it depressed lifts up
(lowers) the RLL during 5 sec., then it stops. For further uplifting (lowering) it is necessary
to press the corresponding button and hold it depressed once again!

Then after the implement has been detached, activation and work on HLL is per-

formed in accordance with clause 2.14.2.

WARNING: WHEN USING THE REMOTE BUTTONS OF RLL CONTROL DO NOT

STAND BETWEEN THE TRACTROR AND ATTACHED IMPLEMENT! TO PREVENT
ACCIDENTS IT IS FORBIDDEN TO USE BUTTONS OF MECHANICAL SHIFTING OF
ELECTRIC VALVES OF REGULATOR EHR23-LS 7 (FIGURE 2.14.2)!

1 – instruction shield on safety rules; 2, 5 – instruction shield of RLL control dia-

gram; 3 – RLL lowering button; 4 – RLL uplift button; 6 – left remote RLL control panel; 7 –
regulator EHR23-LS; 8– right remote RLL control panel.

Figure 2.14.2 – RLL control with remote buttons

https://tractormanualz.com/

«
...
57
58
59
60
61
...
»

Содержание 3522.5





















































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3522.5

Бренд: Jacobsen Страницы: 54

4400 BROCHURE 74-101

Бренд: MASSEY FERGUSON Страницы: 20

Бренд: Claas Страницы: 31

Бренд: RHINO Страницы: 56

Monogram Compactor

Бренд: GE Страницы: 12

Monogram GCG1000

Бренд: GE Страницы: 12

MONOGRAM ZCG3100 BB

Бренд: GE Страницы: 16

Бренд: GE Страницы: 20

Бренд: GE Страницы: 28

Бренд: GE Страницы: 16

Бренд: GE Страницы: 2

Бренд: Iseki Страницы: 98

Бренд: Iseki Страницы: 176

Бренд: New Holland Страницы: 2

Groom Master II

Бренд: Jacobsen Страницы: 24

Бренд: Cadet Страницы: 88

Бренд: SaMASZ Страницы: 42

Бренд: pewag Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды