Belarus 3522.5 Скачать руководство пользователя | Manualshive

Страница: 116 / 340

background image

3522.5-0000010

РЭ

117

3.6 Rear axle

3.6.1 General information

The rear axle consists of a main gear, a differential with locking mechanism, final

drive gears and brakes, arranged in one body.

A reduction part is located in the front section of the rear axle body, it consists of

gears of ranges III and IV of the gearbox, FDA drive gears and a driving bevel gear with a
circular tooth to drive pumps of HLL and of transmission hydraulic system, placed outside
and mounted in one body.

A clutch and a reduction unit of PTO are mounted in the rear section of the rear axle

body.

Pumps of the transmission hydraulic system and of the HLL as well as a speed sen-

sor of rear PTO shaft end extension are mounted on the right side of the rear axle body.

On the left side of the rear axle there is a filler to fill in transmission oil. Oil is filled up

to the level of a pilot hole, located on the right side of the rear axle body.

The oil level is checked with an oil-level gauge 7 (figure 3.6.1). The oil level shall

stay between lower and upper marks of the oil-level gauge. The oil is drained out from the
transmission through a discharge hole with a plug 9.

Axle shaft speed sensors and drain plugs are mounted on the final drive tubes.

1 – plate of rear axle body; 2 – final drive; 3 – hydraulic system pump; 4 – HLL pump; 5

– filler; 6 – speed sensor of rear PTO shaft end extension; 7 – oil-level gauge; 8 – rear PTO; 9
– plug.

Figure 3.6.1 – Rear axle (outside view)

3.6.2 Main gear

The main gear (master pair) is intended to increase turning torque and to change

turning direction from a longitudinal driving shaft to a differential transversally-located rota-
tion of axis.

The main gear is a pair of bevel gears with circular teeth. The driving gear 24 (figure

3.6.3) is made all-in-one piece with the shaft, the driven gear 25 is attached by bolts 26
between the lock body and the differential body. Nuts 28 of the differential bolts are locked
against self-unscrewing pairwise by locking plates 27.

https://tractormanualz.com/

«
...
114
115
116
117
118
...
»

Содержание 3522.5





















































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3522.5

E15TC75HSS - ICON Designer

Бренд: Electrolux Страницы: 2

E15TC75HPS - Fully Integrated Trash Compactor

Бренд: Electrolux Страницы: 44

EI15TC65HS - Undercounter Trash Compactor

Бренд: Electrolux Страницы: 12

EI15TC65HS - Undercounter Trash Compactor

Бренд: Electrolux Страницы: 2

Бренд: Poulan Pro Страницы: 52

Бренд: New Holland Страницы: 41

Бренд: Broan Страницы: 1

Бренд: Toyama Страницы: 56

COMPAX CL Series

Бренд: Zetor Страницы: 114

Бренд: Land Pride Страницы: 26

Бренд: Kioti Страницы: 120

Бренд: J&M Страницы: 31

Бренд: FENDT Страницы: 6

Бренд: Verts Loisirs Страницы: 72

Kubota F 80 Series

Бренд: Tiktite Страницы: 24

Бренд: Benassi Страницы: 24

Sportsman Touring 570 EPS 2021

Бренд: Polaris Страницы: 186

Бренд: Hurricane Страницы: 96

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды