Belarus 3522.5 Скачать руководство пользователя | Manualshive

Страница: 271 / 340

background image

3522.5-0000010 OM

272

6.4.1.10 Task 9. Inspect/clean air conditioner condenser and oil cooling radiator of

HLL and HSC systems

Check cleanness air conditioner condenser core and oil cooling heat radiator of HLL

and HSC systems. If they are clogged, it is necessary to clean the condenser and the ra-
diator with a compressed air. Open the hood and direct an air flow perpendicular to the
condenser plane from top downward. Jammed finning must be planished by means of
special comb or plastic (wooden) plate. In case of severe condenser clogging rinse it with
hot water under pressure not more than 0.2 MPa and blow it off by a compressed air.

- condenser cores must be cleaned both from the hood mask side and from the en-

gine fan side. To do this, heft the air conditioner condenser as indicated in figure 6.4.1.11.

USE OF CORROSIVE DETERGENT COMPOSITION IS FORBIDDEN!

6.4.1.11 Task 10. Inspect/clean the engine water radiator and the engine CAC-

radiator.

Check cleanness of the engine CAC-radiator 1 core (Figure 3.1.3). In case it is

clogged perform the following actions:

- turn off the two air conditioner condensers screws fastening it to the CAC lifting

mechanism;

- pull the lower part of the condenser and anchor it in hefted position by means of

limit stop, placed to the right along the tractor run;

- carry out the CAC-radiator cleaning with the compressed air. Direct an air flow

perpendicular to the CAC-radiator plane from top downward. In case of severe CAC-
radiator clogging rinse it with hot water under pressure not more than 0.2 MPa and blow it
off by a compressed air;

- put the air conditioner condenser back;
- unscrew two winged nuts 10 for 3…5 turns;
- by means of lifting mechanism heft the air conditioner condenser, oil cooling sys-

tem of HLL and HSC systems, CAC, and clean the water radiator with a compressed air.
Direct an air flow perpendicular to the water radiator from top downward. In case of severe
water radiator clogging rinse it with hot water under pressure not more than 0.2 MPa and
blow it off by a compressed air;

- radiator cores must be cleaned both from the hood mask side and from the engine

fan side;

- put the radiators and tighten the winged nut up.

ALKALINE SOLUTIONS AND CORROSIVE DETERGENT COMPOSITION MUST

NOT BE USED!

6.4.1.12 Task 11. Check/rinse of gripper tools of FLL and RLL
Check the pockets where the hinged joint locking mechanism in the gripper tools 2

(Figure 6.4.4) of the RLL. In case of dirt accumulation, clear the internal pockets and rinse
it with water.

1 – link; 2 – gripper tool.

Figure 6.4.4 – Gripper tool of RLL (FLL)

https://tractormanualz.com/

«
...
269
270
271
272
273
...
»

Содержание 3522.5





















































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3522.5

HiTech T Series

Бренд: Valtra Страницы: 31

Бренд: Eagle Страницы: 83

Бренд: Amica Страницы: 60

Бренд: Amica Страницы: 68

Бренд: Daedong Страницы: 196

Бренд: New Holland Страницы: 21

Бренд: New Holland Страницы: 51

Бренд: Winton Страницы: 24

Бренд: Agrison Страницы: 204

Бренд: Sola Страницы: 24

Бренд: Belarus Страницы: 248

Бренд: Troy-Bilt Страницы: 16

'15' Series 2015 4WD

Бренд: Mahindra Страницы: 132

ROBOPOWER 111300001

Бренд: McConnel Страницы: 96

Бренд: Broan Страницы: 10

Бренд: Ariens Страницы: 21

GE PROFILETM GCG1500L

Бренд: GE Страницы: 2

Бренд: Thwaites Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды