Belarus 3522.5 Скачать руководство пользователя | Manualshive

Страница: 257 / 340

background image

3522.5-0000010 OM

258

ATTENTION: WHEN THE IMPLEMENT IS OPERATED WITH THE CARDAN

SHAFT THERE IS A HAZARD OF PROCESS MATERIAL OR THE IMPLEMENT COM-
PONENTS RELEASE, THEREFORE IT IS NESESSARY TO OBSERVE SAFE DIS-
TANCE!

When the implement cardan shaft is coupled to the PTO shaft end the following

rules and requirements shall be observed:

1. Check the engaged RPTO shaft mode (basic or economy mode) for compliance;
2. Before engagement detach the cardan shaft into two parts.
3. Inspect the cardan shaft, PTO shaft and PRS for absence of mechanical damage

and for completeness of the set. Clear the PTO shaft ends of dirt when needed, and lubri-
cate it according to the lubrication chart, specified in the implement operation manual.

4. The cardan shaft part having the icon of “Tractor” on it, shall be coupled to the PTO

shaft end, and the second part – to the implement PRS accordingly. Do not forget to fasten
contactor splined bushings on the PTO and PRS shaft ends properly: fastening method shall
be specified by the cardan shaft manufacturer.

5. The implement cardan shaft end yoke from the side of PTO shaft and PRS shall

be in the same plane as indicated in Figure 5.8.1.

Figure 5.8.1 – Cardan shaft mounting scheme

6. Safety clutch, as indicated in Figure 5.8.2 shall be installed only from the side of

PRS of the drive of the implement coupled, other method of mounting will not ensure the
excess of timely protection of the tractor PTO shaft from the maximum permissible torque.
After lengthy downtime check the implement safety clutch technical condition.

Figure 5.8.2 – Safety clutch mounting scheme

7. Mounting of the cardan shaft with guard housing together with PTO shaft and

PRS protective devices, with retaining chains both from the side of the PTO shaft and of
the PRS, as indicated in Figure 5.8.3, ensures cardan joint safety.

Figure 5.8.3 – Safety cardan shaft mounting scheme

8. When the cardan shaft is used for the first time it is necessary to check the car-

dan shaft length, and to adjust it to the operating conditions with tractors “BELARUS-
3522.5” when needed. For more detailed guidelines on cardan shafts see the technical
documentation enclosed. Contact the cardan shaft manufacturer when needed.

https://tractormanualz.com/

«
...
255
256
257
258
259
...
»

Содержание 3522.5





















































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3522.5

Бренд: Kubota Страницы: 666

Бренд: Sears Страницы: 27

Бренд: Allis-Chalmers Страницы: 220

Бренд: Allis-Chalmers Страницы: 312

Бренд: New Holland Страницы: 2

Бренд: New Holland Страницы: 9

Бренд: Warn Страницы: 15

Бренд: Belarus Страницы: 358

Бренд: Pasquali Страницы: 130

Бренд: LAMBORGHINI Страницы: 41

Бренд: GE Страницы: 16

Бренд: Case IH Страницы: 15

Boomer 1020/T1010

Бренд: New Holland Страницы: 1

Бренд: NU-LIFT Страницы: 7

Бренд: Koyker Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды