manualshive.com logo in svg

Belarus 1822.3, Руководство оператора

"Belarus 1822.3" - Инструкция оператора для скачивания бесплатно на нашем сайте. Подробное описание и инструкции по эксплуатации этого устройства доступны для загрузки. Получите доступ к руководству пользователя "Belarus 1822.3" прямо сейчас на manualshive.com.

Поделиться
Скачать
background image

2022.3-0000010  OM

330

b) It is necessary to check voltage terminal “ ” of the generator with gauges en-

gaged  (SA10 switch key is in the first position “I”) and with the motor stopped. Voltage
should be from 0.8 to 1.2 V, in case it differs correct the trouble in added resistance circuit
R1 (located in SU).

ATTENTION: TEST OF GENERATOR OPERABILITY BY MEANS OF BATTERY

DISCONNECTION, CONNECTION OF TERMINAL “+ ” TO TRACTOR FRAME WITH THE
MOTOR RUNNING CAN RESULT IN GENERATOR BREAKDOWN!

7.15.2.3 Auxiliary AB (GB2) charge is nil with the motor running
Absence of charge (nonoperability of voltage converter UZ1) of auxiliary accumula-

tor battery GB2 can show through low frequency of engine cranking by starter while other
tractor systems and units are properly operating.

Other types of failures and troubleshooting methods are possible:
1. Indicating lamp (red led lamp) on value indicating scale in on-board circuit in in-

strument cluster  2 does not light up after engine start.

It indicates failure of charging rate in auxiliary AB (GB2). Perform the following ac-

tions:

- assure oneself of generator G1 operability as indicated in cl. 7.14.2.2.
- assure oneself of ground on the converter housing UZ1.
- test fuse element FU34 operability with specific power of 20  in the converter

housing UZ1.

- test voltage on terminals “ ” and “-  2” UZ1 in reference to the converter housing

with the motor running and generator properly operating G1. Voltage shall be from 13.5 to
15 V; if voltage is below the specified value restore corresponding circuits “ ” and “-  2”
from generator to voltage converter.

- measured voltage on terminals of auxiliary AB (GB2) in 5 minutes after engine

start-up, the voltage should be within the range from 13.5 to 15 V. If it is below the required
value check circuit continuity from terminal “+  2” of the converter to terminal”30” of the
starter. If the circuit does not operate properly replace the converter UZ1.

Note – Test charging rate from voltage converter can be executed by means of mul-

timeter connection in current measurement mode (measurement range is up to 10A) in-
stead of fuse element, installed on the converter housing. Test should be carried out after
some period of operation, when charging rate is decreased in converter output circuit up to

. Meanwhile in converter output circuit current of 10A should be displayed (depending

on AB charging rate (GB2).

2. Indicating lamp in voltmeter scale in instrument cluster  2 does not light up after

engine start when instruments are engaged with motor not running.

Perform the following:

) check presence of ground on the converter housing, if there is no “ground” –

draw a wire from tractor transmission housing.

b) provide “ground” for  terminal “ ” of the converter UZ1, if indicating lamp does not

light up check circuit “ ” for continuance within the range from the converter UZ1 to in-
strument cluster  2, if the circuit is operational check  instrument cluster  2 or replace
the converter UZ1.

3. Main reasons for nonoperability of properly operating converter UZ1:
- voltage on terminal “ ” of generator is below 5.5 V;
- voltage of on-board circuit is below 12.4 V;
- voltage of on-board circuit exceeds 15.6 V;
- overheating VC at temperature exceeding 110 ° .
- load current at terminal “+ 2 (28 V)” is below 15 m  (bad contact in charging cir-

cuit, terminal corrosion of converter fuse block installation);

Note – Current decrease in charging circuit of auxiliary AB (GB2) is below 15 m

can give evidence of standard accumulator charging, when this happens the converter
shuts down and charge indicating lamp lights up in voltage indicator of ob-board circuit.

https://tractormanualz.com/

Содержание 1822.3







































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1822.3

Textron Steiner 420 Owner'S/Operator'S Manual preview
Steiner 420
Бренд: Textron Страницы: 26
Howard HK 32-250 Operating Instructions & Parts List Manual preview
HK 32-250
Бренд: Howard Страницы: 35
AVANT A36968 Operator'S Manual For Attachment preview
A36968
Бренд: AVANT Страницы: 18
AVANT A36031 Operator'S Manual For Attachment preview
A36031
Бренд: AVANT Страницы: 24
Yancheng Tractor Factory Jinma 200 Series User Manual preview
Jinma 200 Series
Бренд: Yancheng Tractor Factory Страницы: 52
MTD 490-900-0024 Operator'S Manual preview
490-900-0024
Бренд: MTD Страницы: 16
MTD 147-860A Owner'S Manual preview
147-860A
Бренд: MTD Страницы: 26
Kalmar Ottawa t2 Maintenance Manual preview
Ottawa t2
Бренд: Kalmar Страницы: 262
Winton WCF Series Owner'S Manual preview
WCF Series
Бренд: Winton Страницы: 16
Valtra BH Generation 4 Operator'S Manual preview
BH Generation 4
Бренд: Valtra Страницы: 21
Zetor FORTERRA HD Series Operator'S Manual preview
FORTERRA HD Series
Бренд: Zetor Страницы: 168
FENDT 900 Vario Gen6 Series Workshop Service Manual preview
900 Vario Gen6 Series
Бренд: FENDT Страницы: 51
Taylor-Dunn Tiger TC-030-60 Operation, Maintenance, And Replacement Parts Manual preview
Tiger TC-030-60
Бренд: Taylor-Dunn Страницы: 186
Spraying Systems TeeJet Matrix Pro 570G User Manual preview
TeeJet Matrix Pro 570G
Бренд: Spraying Systems Страницы: 127
Knapik Single Row Walking Tractor Manual preview
Single Row Walking Tractor
Бренд: Knapik Страницы: 34
FIORENTINI TX020 User Manual preview
TX020
Бренд: FIORENTINI Страницы: 14
Mitsubishi K3M Maintenance Manual preview
K3M
Бренд: Mitsubishi Страницы: 192

Бренды по названию

Популярные бренды

Загрузить еще бренды