manualshive.com logo in svg

Belarus 1822.3, Руководство оператора

"Belarus 1822.3" - Инструкция оператора для скачивания бесплатно на нашем сайте. Подробное описание и инструкции по эксплуатации этого устройства доступны для загрузки. Получите доступ к руководству пользователя "Belarus 1822.3" прямо сейчас на manualshive.com.

Поделиться
Скачать
background image

2022.3-0000010  OM

192

In construction of rear LL there is a possibility of use of an adjusting rod which by

fixing of the lower links of a certain size among themselves ensures necessary length of a
suspension axis and facilitates their connection to an implement. For protection of coupled
implements from rocking length adjustable limit external rods are used.

To ensure the implement is in the right position the following adjustments of RLL by

means of the upper link, lifting rods and limit turnbuckles are provided in vertical and hori-
zontal plane:

1 Modification of length of upper link
It is carried out in order to ensure equal penetration of operative parts (alignment of

running depth of operative parts located one after another along the tractor run). If
mounted plough carriage reaches forward along the tractor run and the front plough body
cuts deeper than the rear one, extend the upper link; and if the front plough body cuts for
the more shallow depth than the rear one, the upper link shall be shortened.

2 Modification of length of left or right lifting rod.
The modification is carried out in the following cases:
- to ensure the implement is in the horizontal plane;
- to ensure the even depth processing with operative parts of tractor-mounted ma-

chine across the width of cut;

3 Modification of length of both lifting rods, upper link for transport position of the

implement.

The modification is carried out in the following cases:
- to ensure the road clearance is not less than 300 mm;
- to ensure the sufficient safe clearance between the elements of the tractor and the

implement, excluding the contact of parts of the tractor implements (clearance is not less than
100 mm).

4. Modification of length of both turnbuckles.
The modification is carried out in the following cases:
- during transportation of the implement, the turnbuckles shall be blocked for the

limitation of the implement rocking at run for the avoidance of the tractor elements damag-
ing in case of an incidence;

- during operation of mounted, semimounted tilling machines with passively oper-

ated parts for the full processing (share and chisel ploughs, shallow ploughs, rippers and
other implements), free movement in horizontal plane (rocking) shall be ensured, and the
fasteners shall be unblocked as indicated in subsection  3.17.2 “Turnbuckle”;

IT IS FORBIDDEN TO OFFSET THE LONGITUDINAL AXIS OF THE IMPLEMENT,

CONCERNING THE LONGITUDINAL AXIS OF THE TRACTOR BY MEANS OF ADJUST-
MENT OF TURNBUCKLES.

Note – Rules on adjustment of the lifting rods and turnbuckles are specified in sub-

section 3.17 “Rear lift linkage”.

ATTENTION: LENGTH OF THE LEFT LIFTING ROD OF THE REAR LIFT LINK-

AGE MAKES 770 MM, WHICH SHALL NOT BE CHANGED WITHOUT PARTICULAR
NEED. IT IS USUALLY THE RIGHT LIFTING ROD THAT IS LENGH ADJUSTABLE.
WHEN THE CROSSBAR IS USED ON THE SUSPENSION AXIS AND WHEN REVERSI-
BLE  PLOUGH  IS  USED  THE  LENGH  OF  THE  LIFTING  RODS  SHALL  BE  ALL  THE
SAME!

ATTENTION: NONCOMPLIANCE WITH THE REQUIREMENTS FOR ADJUST-

MENT OF TURNBUCKLES AND LIFTING RODS MAY RESULT IN TURNBUCKLE OR
SUPPORT BRACKET BREAK OR OTHER BREAKAGE!

ATTENTION: ESSENTIAL FEATURES AND WAYS OF ADJUSTMENT OF POSI-

TION OF THE IMPLEMENT COUPLED WITH MOUNTED DEVICES ACCORDING TO
THE PECULIARITIES OF TECHNOLOGICAL PROCESS EXECUTION AND AGRO-
TECHNICAL REQUIREMENTS ARE SPECIFIED IN OPERATIONAL DOCUMENTATION
OF SUCH IMPLEMENTS. IF THERE IS NO INFORMATION IN OPERATIONAL DOCU-
MENTATION, YOU SHALL OBTAIL IT FROM THE MANUFACTURER OR SELLER OF
THE IMPLEMENT!

https://tractormanualz.com/

Содержание 1822.3







































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1822.3

MacDon M155 Manual preview
M155
Бренд: MacDon Страницы: 2
MASSEY FERGUSON 4400 BROCHURE 74-101 Brochure preview
4400 BROCHURE 74-101
Бренд: MASSEY FERGUSON Страницы: 20
Kubota STV32 Operator'S Manual preview
STV32
Бренд: Kubota Страницы: 102
Kubota MX5200 Operator'S Manual preview
MX5200
Бренд: Kubota Страницы: 115
Hagie UpFront GST 20 Operator'S Manual preview
UpFront GST 20
Бренд: Hagie Страницы: 120
Valtra BH144 HiTech Operator'S Manual preview
BH144 HiTech
Бренд: Valtra Страницы: 31
Zetor 7520 Operator'S Manual preview
7520
Бренд: Zetor Страницы: 236
Zetor Forterra CL 100 Operator'S Manual preview
Forterra CL 100
Бренд: Zetor Страницы: 198
Zetor COMPAX CL 25 NC Operator'S Manual preview
COMPAX CL 25 NC
Бренд: Zetor Страницы: 108
Zetor 10641 Forterra turbo Operator'S Manual preview
10641 Forterra turbo
Бренд: Zetor Страницы: 315
Trimax Genuine Parts Stealth S3 Repair Parts Instructions preview
Genuine Parts Stealth S3
Бренд: Trimax Страницы: 10
Sears 917.25430 Assembly And Operating Instructions Manual preview
917.25430
Бренд: Sears Страницы: 14
SUMMIT EQUIPMENT S-V95 Maintenance Manual preview
S-V95
Бренд: SUMMIT EQUIPMENT Страницы: 30
SUMMIT EQUIPMENT SC-3248 Safety, Operation & Maintenance Manual preview
SC-3248
Бренд: SUMMIT EQUIPMENT Страницы: 35

Бренды по названию

Популярные бренды

Загрузить еще бренды