manualshive.com logo in svg

Belarus 1822.3, Руководство оператора

"Belarus 1822.3" - Инструкция оператора для скачивания бесплатно на нашем сайте. Подробное описание и инструкции по эксплуатации этого устройства доступны для загрузки. Получите доступ к руководству пользователя "Belarus 1822.3" прямо сейчас на manualshive.com.

Поделиться
Скачать
background image

2022.3-0000010  OM

181

4.3 Safety measures to be taken when operating the tractor

4.3.1 General safety measures to be taken when operating the tractor
Do not operate the tractor in a closed room without required ventilation. Exhaust

gas may result in lethal outcome.

Tractor start-up and operation with the hood opened is not allowed.
It is forbidden to open the hood when the engine is running.
Do not start the engine when staying outside the operator's seat. Starting the en-

gine and manipulating the controls, always stay inside the cab in the operator's seat.

Start the engine by way of towing only at emergency situations and only on the trac-

tor that has passed a 30-hour run-in.

Before starting the engine, engage the parking brake, the front and the rear PTOs

shall be engaged, the range shifting lever shall be in “Neutral” position.

During tractor start there shall be no people under the tractor, in front of it or behind,

as well as between the tractor and the coupled implement or trailer.

Before setting on the move warn people around including those operating the cou-

pled implements using the horn, make sure the parking brake is off and start moving
slowly.

Use safety harnesses (supplied against order) at hauling operations.
Passenger staying in the cab during tractor operation is strictly forbidden. (Passen-

ger may stay in the cab only when an additional seat is installed and hauling operations
are carried out).

Do not leave the tractor on the move.
Performing hauling operations observe traffic regulations, adopted in your country.
Hauling operations may be carried out by operators with not less than two years of

tractor operation experience and those who have passed exams in traffic regulations.

Drive the tractor on slippery roads with automatic DL engaged only at a speed not

higher than 10 km/h.

Using the tractor for hauling operations do the following:

- set a track (1940  20) mm for front and rear wheels;
- check operation of brakes; interlock brake pedals, check and if necessary adjust

the brakes for simultaneity of operation;

- check operation of the parking brake;
- check a condition of devices for light and sound annunciation; hauling trailers shall

have rigid hitches and be linked with a safety chain or a cable;

- never move downhill with the gear disengaged. Move uphill and downhill at the

same gear;

It is forbidden to operate with a trailer without independent brakes, if its weight ex-

ceeds a half of a total actual weight of the tractor. The faster you move and the more
weight you tow, the bigger safety distance shall be.

It is forbidden to drive the tractor with twinned wheels on public roads!

Hauling people inside trailers is forbidden.
Before getting down to work with a trailer turn the compressor on, check the condi-

tion of the trailer brake pneumatic drive and air pressure in the system. Remove the fail-
ures detected. Make sure to connect the trailer brake pneumatic drive. Carry out connec-
tion of the trailer connecting head to the tractor connecting head with the parking brake
engaged.

https://tractormanualz.com/

Содержание 1822.3







































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1822.3

Gardol 155107HRB Instruction Manual preview
155107HRB
Бренд: Gardol Страницы: 108
Zetor COMPAX CL 35 NC Operator'S Manual preview
COMPAX CL 35 NC
Бренд: Zetor Страницы: 114
CID SBC 14-20 GPM Owner'S Manual preview
SBC 14-20 GPM
Бренд: CID Страницы: 58
Husqvarna 96048005800 Repair Parts Manual preview
96048005800
Бренд: Husqvarna Страницы: 36
Husqvarna 96043009000 Illustrated Parts List preview
96043009000
Бренд: Husqvarna Страницы: 18
Husqvarna GTH26V48LS Owner'S Manual preview
GTH26V48LS
Бренд: Husqvarna Страницы: 48
Husqvarna LTH17538 Operator'S Manual preview
LTH17538
Бренд: Husqvarna Страницы: 60
Husqvarna 917.289571 Illustrated Parts List preview
917.289571
Бренд: Husqvarna Страницы: 25
Husqvarna TC 242TX Operator'S Manual preview
TC 242TX
Бренд: Husqvarna Страницы: 280
Husqvarna LTH1842 TWIN Owner'S Manual preview
LTH1842 TWIN
Бренд: Husqvarna Страницы: 44
Husqvarna 96043015100 Repair Parts Manual preview
96043015100
Бренд: Husqvarna Страницы: 36
Husqvarna LT 151 Instruction Manual preview
LT 151
Бренд: Husqvarna Страницы: 76
Husqvarna LTH140 Owner'S Manual preview
LTH140
Бренд: Husqvarna Страницы: 51
Valtra A800R Operator'S Manual preview
A800R
Бренд: Valtra Страницы: 21
Yanmar EB3100 Operator'S Manual preview
EB3100
Бренд: Yanmar Страницы: 164
New Holland T3.60F Service Manual preview
T3.60F
Бренд: New Holland Страницы: 41
KUHN HR6004DR Operator'S Manual preview
HR6004DR
Бренд: KUHN Страницы: 96
Ingersoll-Rand BXR-60 Instruction Manual For Installation / Operation / Maintenance / Parts preview
BXR-60
Бренд: Ingersoll-Rand Страницы: 67

Бренды по названию

Популярные бренды

Загрузить еще бренды