Belarus 1822.3 Скачать руководство пользователя страница 185 | Manualshive

Страница: 185 / 358

background image

2022.3-0000010 OM

184

4.3.2 Fire safety measures
The tractor shall be equipped with fire fighting equipment, i.e. a shovel and a fire

extinguisher. Operating the tractor without fire fighting equipment is forbidden.

Never fuel the tractor with the engine running.
Do not smoke when fueling in the tractor.

Do not fuel the tank to the max. Leave some volume for fuel to expand.

Never add petrol or mixtures to engine fuel. This combination may create increased

danger of inflammation or explosion.

Places for tractor parking, storing of fuel and lubricants shall have a plowed around

band of not less than 3 m width and also be provided with fire extinguishing means.

The tractor must be filled with fuel and lubricants by a mechanic way and with the

engine stopped. Use lighting at night time. It is not recommended to fill in tanks using
buckets. Carrying out repair operations in field conditions using electric/gas welding, clean
parts and assembly units from plant remains.

Prevent the manifold and muffler from getting dirty with fuel, thatch, etc.
Avoid thatch winding around rotating parts of the implements coupled with the trac-

tor.

Washing parts and assembly units with kerosene or gasoline take care to exclude a

possibility of inflammation of flushing fluid vapor.

Do not operate the tractor in places subjected to fire risk with the hood and other

protective units removed from hot parts of the engine.

Do not use open fire to warm up oil in the engine sump, to fill in fuel tanks, to burn

out dirt in a radiator cell.

In case a fire bed occurs, pour some sand onto it, cover with canvas cloth, sack-

cloth or other dense texture. Use a carbon-dioxide fire extinguisher. Do not pour water
over burning fuel and oil.

Make sure there are no flammable materials near the exhaust manifold and the

muffler during engine running.

Harvesting hay and thatch, operating at places with enhanced danger of fire, avoid

amassment of inflammable materials on a muffler guard and on gas links.

Turn the power disconnect switch off when finishing to operate the tractor.

https://tractormanualz.com/

«
...
183
184
185
186
187
...
»

Содержание 1822.3







































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1822.3

Бренд: International Harvester Company Страницы: 94

Бренд: Case IH Страницы: 51

Бренд: Husqvarna Страницы: 68

Бренд: Husqvarna Страницы: 104

Бренд: Sears Страницы: 27

THE GRAIN TRAIN 740

Бренд: brent Страницы: 43

Бренд: New Holland Страницы: 41

Tractor TURBOMIX MTXH

Бренд: Bauer Страницы: 42

Бренд: Shaver Страницы: 56

Бренд: Land Pride Страницы: 50

Proxima GP Series

Бренд: Zetor Страницы: 226

Бренд: Yanmar Страницы: 164

Бренд: Tiger Страницы: 202

BENGAL JD6110-20M/R MY20

Бренд: Tiger Страницы: 223

BENGAL JD6110-30M/R T4F

Бренд: Tiger Страницы: 226

WILDKAT JD6105-25E T4F

Бренд: Tiger Страницы: 240

Бренд: Tiger Страницы: 236

BENGAL JD51 M Series

Бренд: Tiger Страницы: 240

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды