Belarus 1822.3 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 358

background image

2022.3-0000010 OM

13

1 TRACTOR DESCRIPTION AND OPERATION

1.1 Tractor assignment

The

tractor “BELARUS-1822.3/1822 .3/2022.3/2022 .3” is intended for perform-

ance of various general –purpose agricultural operations, for basic and preseeding treat-
ment of soil, planting of crops and other cultures in a structure with wide-span and com-
bined units, for harvesting operations in a structure with heavy-duty harvesting complexes
that are designed for forage conservation, crop harvesting, for transport and loading op-
erations.

Low-speed version of the reverse configuration 2022 .3 – 17/32 of BELARUS-

2022 .3 tractor is also intended to operate with units that have active working elements
driven from the rear PTO and move at low operating speeds.

The version 2022 .3 – 17/32 has the following differences from the basic version:

- the reduced speed range of the front travel includes the speeds of 1,14 km/h to

24,32 km/h;

- the speed range of the reverse travel includes the speeds of 1,60 km/h to 11,46

km/h;

- to increase the clearance a smaller fuel tank is mounted under the lateral fuel tank;
- there is a protection for the rear glass and lights;
- rear wheels have protected valves.

The

tractor “BELARUS-1822.3/2022.3” is a general-purpose wheeled tractor of trac-

tion class 3 with the wheel formula 4X4.

The

tractor “BELARUS-1822.3/2022 .3” is a general-purpose wheeled tractor of

traction class 3 with the wheel formula 4X4 and a reversible control post.

Distinctive features of BELARUS-1822.3/1822 .3 model compared to BELARUS-

2022.3/2022 .3 model are listed in table 1.1.

BELARUS-1822.3/1822 .3

BELARUS-2022.3/1822 .3

Engine -260.9S2,

rated power 132,5 kW

Engine D-260.4S2,

rated power 156 kW

Ballast 1822.3-4235010 (without weights)

Ballast weight 2022-4235010 (with

weights)

The rear PTO has only standard

operation mode, the economy mode is
missing

The rear PTO has both standard

and economy operation modes

Supplementary ballast

2022-4235025- is missing

Supplementary ballast

2022-4235025- is installed on order

Front lift linkage and front PTO are

not mounted

Front lift linkage and front PTO are

not mounted on order

Set for rear wheel twinning is sup-

plied on order

Set for rear wheel twinning is in-

cluded into basic configuration

Appearance of BELARUS-1822.3/1822 .3 tractor and BELARUS-

2022.3/2022 .3 tractor with basic configuration is shown in figure 1.1.1.

Appearance of BELARUS-2022.3/2022 .3 equipped with front PTO and FLL is

shown n figure 1.1.2.

https://tractormanualz.com/

«
...
12
13
14
15
16
...
»

Содержание 1822.3







































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1822.3

Бренд: Zetor Страницы: 108

Бренд: LS tractor Страницы: 218

Бренд: Komatsu Страницы: 6

Бренд: Komatsu Страницы: 6

Бренд: Komatsu Страницы: 6

Бренд: McCulloch Страницы: 60

Бренд: Fort Страницы: 104

Бренд: bergmann Страницы: 98

AutoBoom Rogator 54 Series 1997+

Бренд: Raven Страницы: 40

Бренд: Land Pride Страницы: 36

FORTERRA HSX 100 2014

Бренд: Zetor Страницы: 250

Бренд: GE Страницы: 12

Бренд: Kubota Страницы: 6

Бренд: Komatsu Страницы: 6

Verti-Comb 1800

Бренд: Redexim Страницы: 18

Бренд: wsm Страницы: 16

Бренд: wsm Страницы: 543

Бренд: TILMOR Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды