manualshive.com logo in svg

Belarus 1822.3, Руководство оператора

"Belarus 1822.3" - Инструкция оператора для скачивания бесплатно на нашем сайте. Подробное описание и инструкции по эксплуатации этого устройства доступны для загрузки. Получите доступ к руководству пользователя "Belarus 1822.3" прямо сейчас на manualshive.com.

Поделиться
Скачать
background image

2022.3-0000010  OM

224

Change of rated loading per tire depending on the speed is applied in cases when

the tire is not operated for a long time with high torque on the driving wheels. At field works
and other conditions of continuous operation under high torque you should use figures cor-
responding to the speed of 30 km/h. Tire pressure in excess of 0.16 MPa and under 0.09
MPa shall better not be used.

5.12.9 Application of rear axle differential blocking
The tractor rear axle differential provide means for driving wheels rotation with dif-

ferent rate that is necessary for moving along the curvilinear trajectory and along the rough
road, when right and left rear driving wheels travel over different distance for the same
time period.

The disadvantage of the differential is that it distributes the torque on the wheels in

inverse proportion to gripping abilities of the wheels. If one of the wheels gets in the area
with a low gripping ratio (to ice, for instance) it will skid, rotating with a higher speed
whereby the second wheel will rotate slowly. The tractor will move with a low speed. To
eliminate this drawback there is differential blocking (prevention from running) in an auto-
matic and positive modes.

Tractor operation with differential blocked on a firm and dry surface results in in-

creased loads of transmission components and chassis, and impedes maneuvering.

THE TRACTOR MUST NOT BE OPERATED WITH REAR AXLE DIFFERENTIAL

BLOCKING ENGAGED WHEN THE DRIVING SPEED IS IN EXCESS OF 13 KM/H!

THE TRACTOR MUST NOT BE OPERATED IN TRANSPORT POSITION ON THE

HARD-SURFACE ROADS WITH CONSTANTLY ENGAGED REAR AXIS DIFFERENTIAL
BLOCKING!

5.12.10 Doubling of wheels
To improve the passing ability and drawbar features during operation on boggy areas

on mellow soils (on waterlogged soils, in fields, prepared for seeding), doubling of the tractor
wheels is used. Doubling of wheels in combination with minimum ballasting in standard soil
conditions allows coupling with heavy-duty compound implements in fields with different slope.

ATTENTION: DOUBLE TIRES SHALL NOT BE USED FOR IMPROVEMENT OF LIFTING

AND DRAWBAR POWER AS THEY SERVE FOR PRESSURE RELIEVE DURING OPERATION
IN FIELD!

Effect of wheels doubling on the tractor drawbar dynamix on mellow soils appears as fol-

lows. In the area of the nominal drawbar power and at slow speed slipping is decreasing by 1.4
times and drawbar power is increasing. When operated with low hook drawbar power and at
high speed, the drawbar power of the double-wheeled tractor is less than of single-wheeled
tractor due to the increased rolling resistance.

ATTENTION: IT IS RECOMMENDED NOT TO USE TRACTOR COMPLETED

WITH DOUBLE WHEELS WITH TIRES FILLED WITH WATER SOLUTION AND WITH
HINGED BALLAST LOADS FOR OPERATION WITH THE IMPLEMENTS OF TRAILERS
AND SEMI-TRAILERS TYPE!

USE OF INDIVIDUAL BRAKES DURING OPERATION ON DOUBLED REAR

WHEELES IS FORBIDDEN!

Accumulated carrying capacity of dual tires shall not be 1.7 times larger than carry-

ing capacity of a single tire.

ATTENTION: DOUBLING OF FRONT WHEELS SHALL BE USED ONLY IN EX-

CEPTIONAL CASES. IN CASE OF DOUBLING OF FRONT WHEELS CONSULT YOUR
DEALER!

Note – Instructions on wheels doubling are set forth in subparagraph 4.2.10 “Rear

wheels doubling”.

https://tractormanualz.com/

Содержание 1822.3







































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1822.3

LS tractor MT230E 2020 Operator'S Manual preview
MT230E 2020
Бренд: LS tractor Страницы: 218
Still LTX 70 Original Instructions Manual preview
LTX 70
Бренд: Still Страницы: 186
AUTOCAR E-ACTT Service Manual preview
E-ACTT
Бренд: AUTOCAR Страницы: 20
Steinertractor Atractor Install Instructions preview
Atractor
Бренд: Steinertractor Страницы: 2
New Holland TT55 Service Manual preview
TT55
Бренд: New Holland Страницы: 41
Hardi COMMANDER 4500 Instruction Book preview
COMMANDER 4500
Бренд: Hardi Страницы: 170
FENDT 938 Vario MT Workshop Service Manual preview
938 Vario MT
Бренд: FENDT Страницы: 51
Buhler Versatile 2290 Operator'S Manual preview
Versatile 2290
Бренд: Buhler Страницы: 380
MAGNATRAC MH4800 Operator / Technical Manual preview
MH4800
Бренд: MAGNATRAC Страницы: 86
FARM STAR BSF-1523 Owner'S/Operator'S Manual preview
BSF-1523
Бренд: FARM STAR Страницы: 18
Trac Vac 858-RH Operating And Assembly Manual preview
858-RH
Бренд: Trac Vac Страницы: 9
StarTrac 263-4WD-8G-STAGE-V Owner'S Manual preview
263-4WD-8G-STAGE-V
Бренд: StarTrac Страницы: 100
ROTOTILT S30/150 Manual preview
S30/150
Бренд: ROTOTILT Страницы: 8
GTV PRACTI ECO 600 Assembly Instructions preview
PRACTI ECO 600
Бренд: GTV Страницы: 3
FHM BACKHOE BH 8 Operation And Parts Manual preview
BACKHOE BH 8
Бренд: FHM Страницы: 43
Euro Shatal RP4014-50 Operating Instructions Manual preview
RP4014-50
Бренд: Euro Shatal Страницы: 22
Cucine Oggi EKKO CUBE 40 9000 Assembly Instructions preview
EKKO CUBE 40 9000
Бренд: Cucine Oggi Страницы: 3
Cucine Oggi i.Master Double Assembly Instructions preview
i.Master Double
Бренд: Cucine Oggi Страницы: 5

Бренды по названию

Популярные бренды

Загрузить еще бренды