manualshive.com logo in svg

Belarus 1822.3, Руководство оператора

"Belarus 1822.3" - Инструкция оператора для скачивания бесплатно на нашем сайте. Подробное описание и инструкции по эксплуатации этого устройства доступны для загрузки. Получите доступ к руководству пользователя "Belarus 1822.3" прямо сейчас на manualshive.com.

Поделиться
Скачать
background image

2022.3-0000010  OM

182

Trailers attached to the tractor shall have a braking system, ensuring:

-  trailer brake on movement;
-  brake engagement in case of trailer detachment from the tractor;
-  holding the trailer when staying on slopes;
-  prevention of trailer from pushing the tractor when the travel speed is changed

abruptly.

The trailer shall be linked to the tractor by means of a safety chain.

It is required to check operation of the braking system of tractor-trailer train at a

speed of 3 to 5 km/h.

The travel speed at access ways and at passways shall not exceed 10 km/h.

It is forbidden to drive on reverse to public roads.

Loading (unloading) the trailer engage the parking brake of the tractor.
The tractor, which is used with the trailer on public roads, shall operate with a road-

train sign on in accordance with “Traffic regulations”.

Driving on public roads turn on a flashing beacon, if available.

Do not stop the tractor on slopes. If there is a necessity to stop the tractor engage

the parking brake.

Working on the slopes increase the tractor track to the max.
Working on the slopes with an angle of more than 20° set rear wheel track to the max..
Before exiting the cab disengage the front and rear PTOs, stop the engine, engage

the parking brake and remove the key from the starter switch.

If the engine or the steering are broken down, immediately stop the tractor. Keep in

mind that with the engine stopped it is required to apply much greater force to the steering
wheel to operate the tractor.

In case a failure occurs, immediately stop the tractor and eliminate the fault.
Avoid leakage of electrolyte, coolant, fuel, oil and braking fluid.
Use summer and winter grades of fuel correctly. Fill in the fuel tank at the end of

each day to decrease night condensation of moisture. Fill the tractor only with grades of oil
and lubricants recommended by the manufacturer. It is strictly forbidden to use other lubri-
cants.

It is forbidden to turn off the system of electrical equipment by means of the battery

disconnect switch with the engine running.

Operate the tractor at night-time with lighting devices on and being in good order.
If put to a wrong use, your tractor can be dangerous for you as well as for third per-

sons. Avoid using equipment not intended for installation on the tractor.

Make sure any additional equipment or auxiliary units are mounted correctly and

that they are intended to be used with your tractor.

To prevent the tractor from turning over, keep up with the following precaution

measures when operating the tractor:

- choose safe speed, corresponding to road conditions, especially when moving

cross-country, when crossing ditches, slopes and by sharp turns;

- turn round corners with a speed not higher than 5 km/h, on a slippery road – not

higher than 3 km/h.

- move down the hill with first or second gear engaged.
Note – This list of precaution measures is not exhaustive. To avoid turning over, be

always careful when operating the tractor.

It is forbidden to use the tractor at works where the tractor may turn over.

Do not operate the tractor with gauges out of order.
It is not admitted to inflate tires without pressure control.

Coupling the tractor with agricultural implements comply additionally with safety

measures concerning use of these implements.

Before coupling the tractor with agricultural implements make sure the automatic

grips of the lower and upper links of the RLL are clean and faultless. It is forbidden to op-
erate with the automatic grips out of order, their inner cavities stuffed with dirt and foreign
particles.

If the tractor front part rises off the ground when heavy implements are hinged on

the mechanism of the rear lift linkage, mount front ballast weights.

https://tractormanualz.com/

Содержание 1822.3







































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1822.3

HOLMS TKH Operator'S Instruction preview
TKH
Бренд: HOLMS Страницы: 9
Whirlpool TU800SPPB2 Parts List preview
TU800SPPB2
Бренд: Whirlpool Страницы: 7
Whirlpool TU 4000 Series Use And Care Manual preview
TU 4000 Series
Бренд: Whirlpool Страницы: 12
Whirlpool Trash Masher JTF8500XL User Manual preview
Trash Masher JTF8500XL
Бренд: Whirlpool Страницы: 16
Whirlpool W10318827C Use & Care Manual preview
W10318827C
Бренд: Whirlpool Страницы: 24
Whirlpool TU950QPXB0 Use & Care Manual preview
TU950QPXB0
Бренд: Whirlpool Страницы: 24
MTD 148-860A Owner'S Manual preview
148-860A
Бренд: MTD Страницы: 28
MTD 148-760A Owner'S Manual preview
148-760A
Бренд: MTD Страницы: 28
MTD 144-918-000 Owner'S Manual preview
144-918-000
Бренд: MTD Страницы: 36
GMR STENSBALLE/NESBO FF/LA User Manual preview
STENSBALLE/NESBO FF/LA
Бренд: GMR Страницы: 36
Daedong KIOTI PX9530 Manual preview
KIOTI PX9530
Бренд: Daedong Страницы: 256
Valtra Small A Series Service Manual preview
Small A Series
Бренд: Valtra Страницы: 31
Kubota M7040SUHD Operator'S Manual preview
M7040SUHD
Бренд: Kubota Страницы: 25
Kubota M7040SU Operator'S Manual preview
M7040SU
Бренд: Kubota Страницы: 90
Laney NEXUS 810 Operating Instructions preview
NEXUS 810
Бренд: Laney Страницы: 4
Worksaver 614HC Owner'S/Operator'S Manual preview
614HC
Бренд: Worksaver Страницы: 31
Holder C8.72H Brochure & Specs preview
C8.72H
Бренд: Holder Страницы: 4
Holder Park 70 Operating Manual preview
Park 70
Бренд: Holder Страницы: 87

Бренды по названию

Популярные бренды

Загрузить еще бренды