Beko BEKOMAT BM13i Скачать руководство пользователя

Страница: 48 / 76

9.2 Operating states

Illustration

Description / explanation

Disconnected

•

All LEDs are off.

Switch on / power-on self-test

• All LEDs are on for 1 second.
• The

BEKOMAT

carries out a diagnosis of the

electronics unit.

n = 2

Positive power-on self-test
number of repetitions n = 2x

•

The red ALARM LED is off.

• The green VALVE LED is on while the solenoid valve is

cycling.

• The green POWER LED is on.
• The solenoid valve is cycling.

The

BEKOMAT

switches to normal operation.

n = 20

n = ∞

Negative power-on self-test
number of repetitions n = 20x

• The red ALARM LED is on.
• The green VALVE LED is on while the solenoid valve is

cycling.

• The green POWER LED is on.
• The solenoid valve is cycling.

The

BEKOMAT

goes into fail-safe operation

(continuous loop n = ∞).

• The solenoid valve is cycling once per second.

Ready for operation (normal operating mode)

•

The red ALARM LED is off.

•

The green VALVE LED is off.

• The green POWER LED is on.

BEKOMAT

13i / 13i CO / 13i CO PN50

Original installation and operation manual

48 | 76

Содержание BEKOMAT BM13i













































































Результаты поиска

Содержание BEKOMAT BM13i

Отзывы:

Похожие инструкции для BEKOMAT BM13i

Бренды по названию

Популярные бренды

Beko BEKOMAT BM13i, Перевод оригинального руководства по установке и эксплуатации

Результаты поиска

Содержание BEKOMAT BM13i

Отзывы:

Похожие инструкции для BEKOMAT BM13i

Бренды по названию

Популярные бренды