Beko BEKOMAT BM13i Скачать руководство пользователя | Manualshive

Страница: 50 / 76

background image

10. Maintenance

10.1 Warning notices

DANGER

Pressurised system!

There is a danger of death or serious personal injury resulting from contact with fast or

suddenly escaping fluids or through bursting system parts.

• All maintenance and repair work on the system must be carried out in the depressurised

state and with the system secured against unintentional pressurisation.

• Set up a safety area around the working area during all maintenance and repair work.
• Before pressurisation, check all system pipe connections for leak tightness and tighten if

necessary.

• Slowly pressurise the system.
•

Avoid pressure blows and high differential pressures.

• Assemble all pipes free of mechanical stress.
• Compensate any vibrations occurring in the pipe network by using vibration dampers.
•

Install the feed lines and drain lines as fixed pipes.

DANGER

Electric voltage!

There is a danger of death or serious injuries as well as malfunction and device failure
following contact with components which are in contact with electric voltage.
• Only carry out maintenance and repair work on the product when it has been

disconnected and secured against being switched back on again unintentionally.

• Set up a safety area around the working area during all maintenance and repair work.
• Only operate the product with the cover complete and closed or the housing closed.

DANGER

Use of incorrect spare parts, accessories or materials!

The use of incorrect spare parts, accessories or materials, as well as auxiliary and operating
materials, may result in death or serious injury. Malfunction and device failure as well as
material damage can occur.
•

Only use undamaged original parts, auxiliary and operating materials which are specified

by the manufacturer to complete all work.

• Use only the approved materials and suitable tools for the respective purpose and make

sure that they are in proper working order.

• Only use cleaned pipes that are free of dirt and corrosion.
•

Only use electric components and materials that comply with country-specific

regulations (standards, directives etc.) for electrical safety.

WARNING

Insufficient qualification!

Insufficient qualification of the personnel carrying out work on the product and accessories

can lead to accidents, personal injury and damage to property as well as impair operation.
• All work on the product and the accessories may only be carried out by skilled technical

personnel - customer service.

BEKOMAT

®

13i / 13i CO / 13i CO PN50

Original installation and operation manual

50 | 76

«
...
48
49
50
51
52
...
»

Содержание BEKOMAT BM13i













































































Отзывы:

Нет отзывов

Похожие инструкции для BEKOMAT BM13i

Бренд: Eaton Страницы: 2

Бренд: Salamander Pumps Страницы: 32

Бренд: Zoeller Страницы: 24

Бренд: Jandy Страницы: 16

Бренд: EasyPro Страницы: 4

mr. steam AromaSteam MS AROMA

Бренд: Feel Good Страницы: 20

Бренд: Pfeiffer Vacuum Страницы: 68

SEMI SHIELDED BU5510

Бренд: Rowenta Страницы: 16

Бренд: VOLTOMAT HEATING Страницы: 170

Бренд: K2 Pumps Страницы: 24

Бренд: Daikin Страницы: 44

Бренд: XtremepowerUS Страницы: 14

Бренд: Wanner Engineering Страницы: 24

Бренд: N'oveen Страницы: 12

Бренд: PARAGON OUTDOOR Страницы: 19

Бренд: Powrmatic Страницы: 40

Бренд: F.B. SUBMERSIBLE MOTORS Страницы: 48

aroSTOR VWL B 270/5

Бренд: Vaillant Страницы: 240

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды