Beko BEKOMAT BM13i Скачать руководство пользователя | Manualshive

Страница: 33 / 76

background image

5. Transport and storage

WARNING

Insufficient qualification!

Insufficient qualification of the personnel carrying out work on the product and accessories

can lead to accidents, personal injury and damage to property as well as impair operation.
• The work on the product and accessories described below may only be executed and

documented by skilled personnel - transport and storage.

CAUTION

Inappropriate transport or storage!

Inappropriate transport or storage may result in personal injury or damage to the device.
•  Use personal protective equipment during all work with packaging material.
•  Handle packaging, the product and accessories carefully.
•  Pack all parts impact-proof using suitable material.
•  Transport and handle the packaging according to the markings (note lifting gear

attachment points, the centre of gravity and alignment e.g. keep vertical, do not throw
etc.).

• Only use proper means of transport and lifting equipment that is in proper working

order.

• Always adhere to the permissible transport and storage parameters.
• Store the product and accessories only outside of areas exposed to direct sunlight and

heat sources.

NOTE

Handling packaging material!

Inappropriate disposal of packaging materials can cause environmental damage.

• Dispose of the packaging material in accordance with the applicable legal requirements

and provisions of the country and place of use.

5.1 Transport

After transporting and removing the packaging material, inspect the product for possible transport damage. If you find

such damage, notify the carrier company,

BEKO

TECHNOLOGIES or one of its agents immediately.

Transport the product as follows:
• Only transport the product in its original packaging.
• Handle packaging and the product with care.
•

Note the transport weight specification and marking on the packaging.

• Secure the packaging and the product against slipping and falling during transport.

5.2 Storage

Store the product and the accessories as follows:
• Adhere to the storage parameters in chapter “4.2 Storage and transportation parameters” on Page 28.
• Store in a closed, dry as well as frost-free room.
•

Store protected from external influences of the weather, direct sunlight and sources of heat.

• Secure against falling over and protect against vibrations at the storage location.

Original installation and operation manual

BEKOMAT

®

13i / 13i CO / 13i CO PN50

33 | 76

«
...
31
32
33
34
35
...
»

Содержание BEKOMAT BM13i













































































Отзывы:

Нет отзывов

Похожие инструкции для BEKOMAT BM13i

Бренд: SAB Страницы: 7

Бренд: Oasis Страницы: 44

Бренд: Gardena Страницы: 17

Бренд: Gardena Страницы: 12

Бренд: ProMinent Страницы: 81

Бренд: Webasto Страницы: 12

Бренд: Vagner Pool Страницы: 35

Бренд: Oase Страницы: 70

Бренд: Annovi Reverberi Страницы: 100

Бренд: Wilo Страницы: 16

S-THERM+ SHP-140ERC

Бренд: Sinclair Страницы: 18

DUSTTRAK 8530EP

Бренд: TSI Instruments Страницы: 2

Бренд: ProBreeze Страницы: 44

HPW1200/100-440

Бренд: Dynaset Страницы: 11

Бренд: CALEFACTIO Страницы: 2

Бренд: Little Giant Страницы: 12

LEUCO HAWK NMT-EBCH Series

Бренд: Kärcher Страницы: 25

Бренд: Tonon Forty Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды