Beko BEKOMAT BM13i Скачать руководство пользователя | Manualshive

Страница: 11 / 76

background image

2.5.3 Electric voltage

Contact with live components may result in serious personal injuries or death.
To ensure the safe handling of live components, observe the following points:
• Set up a safety area around the working area during all installation and repair work.
• Before starting work, de-energise the product and accessories and secure them against being switched back on again

unintentionally.

• Only connect the product and the accessories to the voltage supply if they are undamaged.
•

Adhere to all applicable regulations (e.g. VDE 0100 / IEC 60364 / ATEX) during installation.

• Connect the protective conductor (earth connection) according to regulations.
• Only operate the product and accessories with the cover complete and closed or the housing closed.

2.5.4 Transport and storage

Inappropriate transport or storage may result in personal injury or damage to property.
For safe transport and storage of the product and accessories, observe the following points:
•  Use personal protective equipment during all work with packaging material.
•  Handle packaging, the product and accessories carefully.
•  Transport and handle the packaged product and accessories according to the markings on the packaging (note lifting

gear attachment points, the centre of gravity and alignment e.g. keep vertical, do not throw etc.).

•  Only use proper means of transport and lifting equipment that is in proper working order.
•  Always adhere to the permissible transport and storage parameters.
•  Store the product and accessories only outside of areas exposed to direct sunlight and heat sources.

2.5.5 Installation

Inappropriate assembly or electrical installation of the product and accessories may result in personal injury and damage
to property as well as impair operation.
For safe assembly and electrical installation, observe the following points:
• Install the product, the accessories, and all parts and materials used so that they are not subject to mechanical

tension.

•

Check all plug-type connections for a correct fit.

• Avoid a stumbling hazard by routing cables and hoses accordingly.
• Avoid mechanical strain on the cables.
•

Fix and fasten hoses in such a way that they cannot flap around.

•

Install the feed lines and drain lines as fixed pipes.

Original installation and operation manual

BEKOMAT

®

13i / 13i CO / 13i CO PN50

11 | 76

«
...
9
10
11
12
13
...
»

Содержание BEKOMAT BM13i













































































Отзывы:

Нет отзывов

Похожие инструкции для BEKOMAT BM13i

Бренд: Watson Marlow Pumps Страницы: 131

Бренд: Eaton Страницы: 57

Бренд: Zenit Страницы: 35

Бренд: Underhill Страницы: 2

Бренд: Aspen Pumps Страницы: 13

Бренд: Modine Manufacturing Страницы: 28

Бренд: usha Страницы: 8

Бренд: Larzep Страницы: 14

DONYER POWER CH-1500

Бренд: Intertek Страницы: 12

Бренд: Crivit Страницы: 23

UNI_SAUNA_B4.5KW

Бренд: UNIPRODO Страницы: 17

Бренд: Masterflex Страницы: 67

Бренд: BLACKMER Страницы: 12

Бренд: IBAIONDO Страницы: 7

Бренд: Stahls Hotronix Страницы: 15

RAC15HL ScreenZone

Бренд: Claudgen Страницы: 20

Бренд: DROPSA Страницы: 9

MENAI D E - MOUNTING

Бренд: RADSON Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды