Beckman Coulter Allegra X-14 sERIES Скачать руководство пользователя страница 49

PN B07493AD

Warranty-1

Beckman Coulter, Inc.

Allegra X-14 Series Centrifuge Warranty

Subject to the exceptions and upon the conditions specified below and the warranty clause of the 

Beckman Coulter, Inc. terms and conditions in effect at the time of sale, Beckman Coulter agrees to correct 

either by repair or, at its election, by replacement, any defects of material or workmanship which develop 

within one (1) year after delivery of an Allegra X-14 series centrifuge (the product), to the original buyer by 

Beckman Coulter or by an authorized representative, provided that investigation and factory inspection by 

Beckman Coulter discloses that such defect developed under normal and proper use.

Some components and accessories by their nature are not intended to and will not function for as long as one 

(1) year. A complete list of such components or accessories is maintained at the factory and at each 

Beckman Coulter District Sales Office. The lists applicable to the products sold hereunder shall be deemed to 

be part of this warranty. If any such component or accessory fails to give reasonable service for a reasonable 

period of time, Beckman Coulter will repair or, at its election, replace such component or accessory. What 

constitutes either reasonable service and a reasonable period of time shall be determined solely by 

Beckman Coulter.

Replacement

Any product claimed to be defective must, if requested by Beckman Coulter, be returned to the factory, 

transportation charges prepaid, and will be returned to Buyer with the transportation charges collect unless 

the product is found to be defective, in which case Beckman Coulter will pay all transportation charges.

Conditions

Beckman Coulter makes no warranty concerning products or accessories not manufactured by it. In the event 

of failure of any such product or accessory, Beckman Coulter will give reasonable assistance to the Buyer in 

obtaining from the respective manufacturer whatever adjustment is reasonable in light of the manufacturer’s 

own warranty.
Beckman Coulter shall be released from all obligations under all warranties, either expressed or implied, if 

the product(s) covered hereby are repaired or modified by persons other than its own authorized service 

personnel, unless such repair in the sole opinion of Beckman Coulter is minor, or unless such modification is 

merely the installation of a new Beckman Coulter plug-in component for such product(s).

Disclaimer

IT IS EXPRESSLY AGREED THAT THE ABOVE WARRANTY SHALL BE IN LIEU OF ALL WARRANTIES OF FITNESS 

AND OF THE WARRANTY OF MERCHANTABILITY AND THAT BECKMAN COULTER, INC., SHALL HAVE NO 

LIABILITY FOR SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND WHATSOEVER ARISING OUT OF THE 

MANUFACTURE, USE, SALE, HANDLING, REPAIR, MAINTENANCE, OR REPLACEMENT OF THE PRODUCT.

Содержание Allegra X-14 sERIES























































Отзывы: