Beckhoff EL1258, Документация

Страница: 248 / 311

Commissioning
EL125x, EL2258 248 Version: 2.5
Index 6pp0 TSO Inputs (for 08 ≤ pp ≤ 0F; Ch. 1 to Ch. 8)
Index (hex) Name Meaning Data type Flags Default
6pp0:0 TSO Inputs UINT8 RO 0x00 (0
dec
)
6pp0:01 Feedback Returns the current value of the output BOOLEAN RO 0x00 (0
dec
)
Index F611 DEV Inputs
Index (hex) Name Meaning Data type Flags Default
F611:0 DEV Inputs UINT8 RO 0x00 (0
dec
)
F611:02 Undervoltage Up The nominal voltage at the power contacts was signifi-
cantly below the minimum value. BOOLEAN RO 0x00 (0
dec
)
F611:03 Overtemperature Overtemperature fault: The temperature of the input or
output blocks is too high. For output terminals check
whether one of the channels is affected by a short cir-
cuit. BOOLEAN RO 0x00 (0
dec
)
F611:04 Checksum error An error occurred in the internal data transfer BOOLEAN RO 0x00 (0
dec
)
F611:21 SysTime DC timestamp of the last input mapping. This time-
stamp should not be used as reference
(information
on DC reference times). [ } 133]
UINT64 RO
6.8.3.1.4 Output data
Index 7pp1 MTO outputs (for 00 ≤ pp ≤ 07; Ch. 1 to Ch. 8)
Index (hex) Name Meaning Data type Flags Default
7pp1:0 MTO outputs UINT8 RO 0x00 (0
dec
)
7pp1:01 Output buffer reset Removes all elements from the buffer
Clearing can be achieved through a rising edge or con-
tinuously by applying 1 at this bit. The behavior can be
parameterized via CoE object
0x8pp1:11 [
}
247] .
BOOLEAN RO 0x00 (0
dec
)
7pp1:02 Manual output state This bit can be used to switch the output without using
timestamps.
• Method 1: The CoE object 0x8pp1:02 [
}
247]
("Enable manual operation") is set to TRUE.
Timestamp mode is now switched off, and the
output can only be switched via the bit "Manual
operation state". This is particularly helpful for
the commissioning phase.
• Method 2: Via the bit "Enable manual
operation" (0x7pp1:04) the channel output can
be forced to the value of this object. Timestamp
processing continues in the background. Output
is only reactivated if the bit "Enable manual
operation" is set to 0 again.
BOOLEAN RO 0x00 (0
dec
)
7pp1:03 Force order This bit defines how to deal with timestamps that were
placed in the past
(see diagram) [ } 126] .
BOOLEAN RO 0x00 (0
dec
)
7pp1:04 Enable manual opera-
tion
See "Manual output state" (0x7pp1:02) [ } 248] .
BOOLEAN RO 0x00 (0
dec
)
7pp1:09 Output order counter Incrementing this byte indicates to the channel that
new output events can be accepted UINT8 RO 0x00 (0
dec
)
7pp1:11 No of output events Number of filled "Output event state" and "Output
event time" objects UINT8 RO 0x00 (0
dec
)
7pp1:21 Output event state 1 This bit is used to specify which state the output should
assume at the time of "Output event time 1" BOOLEAN RO 0x00 (0
dec
)
7pp1:2A Output event state 10 ... BOOLEAN RO 0x00 (0
dec
)
7pp1:41 Output event time 1 Time at which the state described in "Output event
state 1" is to be applied UINT32 RO 0x00000000
(0
dec
)
7pp1:4A Output event time 10 ... UINT32 RO 0x00000000
(0
dec
)