Beckhoff EL1258, Документация

Страница: 139 / 311

Commissioning
EL125x, EL2258 139 Version: 2.5
Index 6pp0 TSI Inputs (for 08 ≤ pp ≤ 0F; Ch. 1 to Ch. 8)
Index (hex) Name Meaning Data type Flags Default
6pp0:0 TSI Inputs UINT8 RO 0x00 (0
dec
)
6pp0:01 Input Current input status BOOLEAN RO 0x00 (0
dec
)
6pp0:09 Status Bit0: Is set for one cycle if a rising edge was detected.
Bit1: Is set for one cycle if a falling edge was detected. UINT8 RO 0x00 (0
dec
)
6pp0:41 LatchPos Timestamp of the rising edge UINT64 RO
6pp0:42 LatchNeg Timestamp of the falling edge UINT64 RO
Index F611 DEV Inputs
Index (hex) Name Meaning Data type Flags Default
F611:0 DEV Inputs UINT8 RO 0x21 (33
dec
)
F611:02 Undervoltage Up The nominal operating voltage at the power contacts
was significantly below the minimum value. BOOLEAN RO 0x00 (0
dec
)
F611:03 Overtemperature Overtemperature fault: The temperature of the input or
output blocks is too high. For output terminals check
whether one of the channels is affected by a short cir-
cuit. BOOLEAN RO 0x00 (0
dec
)
F611:04 Checksum error An error occurred in the internal data transfer BOOLEAN RO 0x00 (0
dec
)
F611:21 SysTime DC timestamp of the last input mapping. This time-
stamp should not be used as reference.
(information
on DC reference times). [ } 133]
UINT64 RO
6.8.1.1.4 Output data
Index 7pp0 MTI outputs (for 00 ≤ pp ≤ 07; Ch. 1 to Ch. 8)
Index (hex) Name Meaning Data type Flags Default
7pp0:0 MTI outputs UINT8 RO 0x00 (0
dec
)
7pp0:01 Input buffer reset Removes all elements from the buffer
Clearing can be achieved through a rising edge or con-
tinuously by applying 1 at this bit. The behavior can be
parameterized via the CoE object
0x8pp0:11 [
}
137]
("Buffer reset behavior").
BOOLEAN RO 0x00 (0
dec
)
7pp0:11 Input order counter This bit indicates to the terminal that the input events
were accepted from the process image and the termi-
nal can copy a new set of input events from the buffer
into the process image during the next cycle
(see buf-
fer mode). [
}
122]
UINT8 RO 0x00 (0
dec
)
6.8.1.1.5 Diagnostic data
Index App0 MTI Diag data (for 00 ≤ pp ≤ 07; Ch. 1 to Ch. 8)
Index (hex) Name Meaning Data type Flags Default
App0:0 MTI Diag data UINT8 RO 0x02 (2
dec
)
App0:01 Overtemperature The internal terminal temperature is above the valid
range. For terminals with output channels check the
outputs for short circuit. BOOLEAN RO 0x00 (0
dec
)
App0:02 Undervoltage The voltage at the power contacts is outside the valid
range. BOOLEAN RO 0x00 (0
dec
)
Index A001 MTI common Diag data
Index (hex) Name Meaning Data type Flags Default
A001:0 MTI common Diag
data UINT8 RO 0x11 (17
dec
)
A001:11 Checksum error
counter An error occurred in the internal data transfer UINT16 RO 0x0000 (0
dec
)