manualshive.com logo in svg

Bacci MASTER, Инструкция по эксплуатации и обслуживанию

"Tau MASTER" - это профессиональное обслуживание устройства с бесплатным руководством по техническому обслуживанию. Загрузите подробное пошаговое руководство по обслуживанию в manualshive.com бесплатно. Получите подробные инструкции и рекомендации для поддержания вашего устройства в отличном состоянии.

Поделиться
Скачать
background image

MASTER

 – 

Instruction manual 

 

Chap. 5 
- 

2

/62 - 

INDEX 

 

5  Controls and use of the machine.......................................................................................... 1

 

5.1

 

Location of machine control panels .................................................................................................. 3

 

5.2

 

Machine controls ................................................................................................................................ 4

 

5.2.1

 

Main  switch .......................................................................................................................................... 6

 

5.2.2

 

Main pushbutton panel ......................................................................................................................... 7

 

5.2.3

 

Portable pushbutton panel .................................................................................................................. 10

 

5.2.4

 

Right and left bench pushbutton panel ................................................................................................ 13

 

5.2.5

 

Right and left bench control pedal ....................................................................................................... 14

 

5.3

 

Operating procedures ...................................................................................................................... 15

 

5.4

 

Procedures to turn on, start and run the machine .......................................................................... 15

 

5.4.1

 

Start-up procedure – preliminary operations ........................................................................................ 16

 

5.4.2

 

Start-up procedure – Turning on the machine...................................................................................... 18

 

5.4.3

 

Start-up procedure – Reset to zero ..................................................................................................... 20

 

5.4.4

 

Preheating the spindles ...................................................................................................................... 23

 

5.5

 

Procedure to turn off the machine ................................................................................................... 24

 

5.5.1

 

Procedure to turn off the machine for longer than two hours ................................................................ 26

 

5.6

 

Machine stop and restart procedures.............................................................................................. 27

 

5.6.1

 

Stop and restart procedure for EMERGENCY intervention................................................................... 28

 

5.6.2

 

Stop and restart procedure for controlled stop intervention STOP ........................................................ 30

 

5.6.3

 

Stop and restart procedure for controlled stop - RESET....................................................................... 31

 

5.6.4

 

Machine stop during machining .......................................................................................................... 32

 

5.7

 

Operating procedures ...................................................................................................................... 33

 

5.7.1

 

Operating modes ............................................................................................................................... 33

 

5.7.2

 

Operating mode - Manual ................................................................................................................... 34

 

5.7.3

 

Operating mode - Automatic ............................................................................................................... 36

 

5.7.4

 

Work  cycles ....................................................................................................................................... 37

 

5.8

 

Equipping the machine .................................................................................................................... 39

 

5.9

 

Tools ................................................................................................................................................. 40

 

5.9.1

 

General information regarding machine tools ...................................................................................... 40

 

5.9.2

 

Machine tool diameter and weight....................................................................................................... 41

 

5.9.3

 

Sharpening machine tools .................................................................................................................. 41

 

5.9.4

 

Machine tool assembly information ..................................................................................................... 42

 

5.9.5

 

Balancing machine tools ..................................................................................................................... 43

 

5.9.6

 

Cleaning machine tools ...................................................................................................................... 44

 

5.10

 

Tool load and presetting .................................................................................................................. 45

 

5.11

 

Loading and blocking pieces for machining ................................................................................... 47

 

5.11.1

 

“TGV” variable geometry table ............................................................................................................ 47

 

5.11.2

 

Adjusting the “TGV” variable geometry table ....................................................................................... 48

 

5.11.3

 

Joining the 2 variable geometry tables ................................................................................................ 48

 

5.11.4

 

Rotating the resting surfaces .............................................................................................................. 49

 

5.11.5

 

Using vacuum modules ...................................................................................................................... 49

 

5.11.6

 

Checking for correct piece blocking .................................................................................................... 50

 

5.12

 

Machining check............................................................................................................................... 51

 

5.13

 

Programming .................................................................................................................................... 52

 

5.13.1

 

Overview ........................................................................................................................................... 52

 

5.13.2

 

Provideo: Managing the piece programme .......................................................................................... 54

 

5.13.3

 

Softkey .............................................................................................................................................. 55

 

5.13.4

 

Part Programme Softkey Bar .............................................................................................................. 55

 

5.13.5

 

Editor Softkey Bar .............................................................................................................................. 56

 

5.13.6

 

BACCI Softkey Bar............................................................................................................................. 57

 

5.14

 

La ISO Programming ........................................................................................................................ 59

 

5.14.1

 

Management  codes ............................................................................................................................ 59

 

5.14.2

 

Management plus variables ................................................................................................................ 60

 

5.14.3

 

The MASTER programme .................................................................................................................. 60

 

5.14.4

 

Example of “masterped” ..................................................................................................................... 61

 

5.14.5

 

Comments or hidden text ................................................................................................................... 62

 

5.14.6

 

Operating sequence in automatic mode (AUTO) ................................................................................. 62

 

5.14.7

 

Operating sequence in manual mode (MANUAL) ................................................................................ 62

 

 

 

Содержание MASTER















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MASTER

ICS Schneider Messtechnik HT10 User Manual preview
HT10
Бренд: ICS Schneider Messtechnik Страницы: 124
GE Profile Series Installation And Startup preview
Profile Series
Бренд: GE Страницы: 24
ABI Attachments Infield Rascal Pro Setup Manual preview
Infield Rascal Pro
Бренд: ABI Attachments Страницы: 8
Abicor Binzel BRS-LC Operating Instruction preview
BRS-LC
Бренд: Abicor Binzel Страницы: 84
ABI Attachments ABI Force Z-23 Product Instruction Sheet preview
ABI Force Z-23
Бренд: ABI Attachments Страницы: 5
abem Terrameter LS User Manual preview
Terrameter LS
Бренд: abem Страницы: 47
Abely LiftMeUp Frequently Asked Questions preview
LiftMeUp
Бренд: Abely Страницы: 5
J.P. SELECTA 3000974 Instruction Manual preview
3000974
Бренд: J.P. SELECTA Страницы: 32
OAKWORKS QuickLock Instructions preview
QuickLock
Бренд: OAKWORKS Страницы: 2
Oakton pHTestr 30 Operating Instructions preview
pHTestr 30
Бренд: Oakton Страницы: 2
Oakton pH 5+ Operating Manual preview
pH 5+
Бренд: Oakton Страницы: 2
O2matic OMC PC-100 Quick Manual preview
OMC PC-100
Бренд: O2matic Страницы: 4
Yamaha TG300 Sound List & Midi Data preview
TG300
Бренд: Yamaha Страницы: 39
Yamaha MU100 Supplementary Manual preview
MU100
Бренд: Yamaha Страницы: 110
RAM MICROLAB 350 User Manual preview
MICROLAB 350
Бренд: RAM Страницы: 4
Hella Gutmann mega macs 50 Quick Start Manual preview
mega macs 50
Бренд: Hella Gutmann Страницы: 48
BRAND Micro-classic Operating Manual preview
Micro-classic
Бренд: BRAND Страницы: 21
Milestone 370635 Operator'S Manual preview
370635
Бренд: Milestone Страницы: 40

Бренды по названию

Популярные бренды

Загрузить еще бренды