Bacci MASTER Скачать руководство пользователя страница 106 | Manualshive

Страница: 106 / 238

background image

CHAPTER 4 –

Installation

Chap. 4

-

23

/32 -

4.6 Loading, transport and unloading

The procedure provided below describes the main instructions for machine loading, transport and
unloading.

PROCEDURE

1 of 1

MEANS

DESCRIPTION

Safety

checks

Loading and unloading must only be performed by qualified and authorised

personnel.
Mark off the loading and unloading area and inform the persons exposed of the
operations under way

Loading

The machine is shipped disassembled in different parts anchored using wooden

cross-beams, belts or similar devices, needed for cargo containment and stowage.

The cargo is always protected against bad weather with large PVC sheets.

Transport

Special attention must be paid to over-sized cargos.
The maximum height of a cargo transported by road haulage is 4 metres, taking

into consideration the height of the means of transport and the cargo being
transported. Certain cargos are shipped by special trucks with a lower loading
platforms to meet the 4 metre limitation.

Pay attention to machines shipped in OPEN TOP type containers, with an extra

height. In such cases

Paolino

Bacci Srl

. guarantees transport up to the ship.

Unless otherwise agreed upon, the customer is responsible for arranging for
suitable means of road haulage from the destination harbour to the installation site.

Inspection

upon

arrival

Visually inspect the cargo and check that the large PVC sheets are integral and do

not have any cuts.

Once the large PVC sheets have been removed, check that the cargo has not

shifted, that the belts are still in place and tensioned and that the wooden cross-
beams are well fastened to the cargo.

If the machine has been damaged, please inform the carrier and the

Paolino

Bacci Srl

technician immediately.

Unloading

  Always start unloading the smallest objects that are easy to reach.
  Unload one freight unit at a time.
  Identify the hooking points of the freight units and always fasten the hoisting

devices before removing the belts and cross-beams which block the freight.

Start hoisting operations gradually, by moving the freight without colliding against

the means of transport.

«
...
104
105
106
107
108
...
»

Содержание MASTER















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MASTER

Бренд: Taber Страницы: 27

Бренд: National Instruments Страницы: 16

Бренд: Jasco Страницы: 11

Бренд: Obdstar Страницы: 42

Бренд: jablotron Страницы: 2

Бренд: Keller Страницы: 12

Бренд: MacDon Страницы: 49

Бренд: MacDon Страницы: 49

Бренд: MacDon Страницы: 4

Бренд: Major tech Страницы: 12

Бренд: PASCO Страницы: 30

Бренд: Lafayette Страницы: 10

Бренд: WARPP Страницы: 28

Бренд: Safco Страницы: 2

Бренд: Maselec Страницы: 6

Бренд: EHEIM classic Страницы: 128

MINOR 2000 G.E.

Бренд: Oscartielle Страницы: 44

Бренд: Heidolph Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды