manualshive.com logo in svg

Bacci MASTER, Инструкция по эксплуатации и обслуживанию

"Tau MASTER" - это профессиональное обслуживание устройства с бесплатным руководством по техническому обслуживанию. Загрузите подробное пошаговое руководство по обслуживанию в manualshive.com бесплатно. Получите подробные инструкции и рекомендации для поддержания вашего устройства в отличном состоянии.

Поделиться
Скачать
background image

MASTER

 – 

Instruction manual 

 

Chap. 5 
- 

62

/62 - 

 

5.14.5 

Comments or hidden text 

 
Everything that is written on the line after the semicolon is ignored by the CN.  Therefore, lines that are 
not to be executed may be “hidden” by entering the symbol “ ; ” before the line or adding comments to 
improve code comprehension.  
 

5.14.6 

Operating sequence in automatic mode (AUTO)  

 
When the master is executed for the first time (first cycle), the axis go to the initial position (safety 
position) and the machine waits for the operator to block the piece and close the door. The repeated 
sequence will be: 

  Stand-by for left hand blocking 
  Stand-by for left door to be closed 
  [execution left programme] 
  Left piece unblocked and loading door opened 
  Stand-by for right hand blocking 
  Stand-by for right door to be closed 
  [execution right programme] 
  Right piece unblocked and loading door opened 

 

When the door is closed, the blocking pressure increases from 2 to 6 bar for safety reasons. 
Furthermore, low pressure may be adjusted by means of two pressure regulators (right and left) located 
in the pneumatic box.  

  

Note: When the loading door is closed, the blocking/unblocking pedal is disabled.

 

 

To use vacuum blocking, just turn on the vacuum pump (using the respective pushbuttons on the 
operator panel) and follow the same blocking procedure with the presses. The vacuometer located near 
the loader will show the operator if the operation has been successful (or not)

.  

 
 

5.14.7 

Operating sequence in manual mode (MANUAL)   

 
In manual mode, the loading doors may be opened and closed by pressing the black pushbutton 
(“DOOR” or “START”) located beside the doors. The piece may be blocked and unblocked (at low 
pressure) by using the special pedal, only if the door is open.   
As in automatic mode, the blocking pressure increases from about 2 bar (low pressure) to 6 bar when 
the doors are closed.  
 

NOTE 

Safety 

warning 

 

 DANGER! 

Danger of flying pieces or tool parts.  

The vacuum pumps may be turned off only when the blocking systems on both 
benches are in the unblocking stage. 

 

 
 

 

Содержание MASTER















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MASTER

Laica SB2200 Instructions And Guarantee preview
SB2200
Бренд: Laica Страницы: 4
Keithley 3330 Operator'S Manual preview
3330
Бренд: Keithley Страницы: 149
Baker D30R User Manual preview
D30R
Бренд: Baker Страницы: 82
Parker Research Corp B100 Operating Instructions preview
B100
Бренд: Parker Research Corp Страницы: 4
Eastwood B100 Instructions Manual preview
B100
Бренд: Eastwood Страницы: 20
Daihan Scientific WiseSpin CF-10 Operation Manual preview
WiseSpin CF-10
Бренд: Daihan Scientific Страницы: 43
Tascam HS-20 Owner'S Manual preview
HS-20
Бренд: Tascam Страницы: 128
ParaBody 842 User Manual preview
842
Бренд: ParaBody Страницы: 6
iHealth PO3M Quick Start Manual preview
PO3M
Бренд: iHealth Страницы: 8
unios Echo Quick Installation Manual preview
Echo
Бренд: unios Страницы: 2
National Instruments VirtualBench Calibration Procedure preview
VirtualBench
Бренд: National Instruments Страницы: 73
M-Audio Rack-mountable 8 x 8 USB 2.0 Interface with MX Core DSP Technology... User Manual preview
Rack-mountable 8 x 8 USB 2.0 Interface with MX Core DSP Technology...
Бренд: M-Audio Страницы: 25
Garmin FUSION APOLLO MS-WB675 Installation Instructions Manual preview
FUSION APOLLO MS-WB675
Бренд: Garmin Страницы: 18
Rapid Shape RS wash Quick Start Manual preview
RS wash
Бренд: Rapid Shape Страницы: 12
Hanskamp MultiFill 003-561-005 Installation And Operating Instructions Manual preview
MultiFill 003-561-005
Бренд: Hanskamp Страницы: 20
Öhlins FCX 0301 Mounting Instructions preview
FCX 0301
Бренд: Öhlins Страницы: 8
?HC HC1200EB Quick Start Manual preview
HC1200EB
Бренд: ?HC Страницы: 2
Unika PRO IS2 User Manual preview
PRO IS2
Бренд: Unika Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды