AUX E Series Скачать руководство пользователя страница 199 | Manualshive

Страница: 199 / 240

background image

AUX air conditioner service manual

196

pressure hose with vacuum pump and vacuum the system.

②

Tighten thimble head; Discharge air in the hose with refrigerant steam in system or refrigerant in

the bottle. If small refrigerant bottle has been connected with hose and vacuum pumping has been
done, there’s no need to discharge air.

③

Start up air conditioner, check low pressure value when it runs stably and judge the remaining

refrigerant in system. Open valve on the refrigerant bottle and then refrigerant enters into refrigerating
system. At the same time, we should observe and control low pressure; continue to fill the refrigerant
until pressure reaches standard evaporate pressure.

④

Refrigerant from low pressure valve is in gaseous form. When gas pressure in bottle is no longer

larger than pressure in system, we shall heat the bottle with warm water so as to promote gaseous
pressure in bottle and push refrigerant continue to flow into system. Do not stand refrigerant bottle
upside down to avoid liquid slugging accident.

⑵

Add refrigerant with high pressure valve

Connect high pressure valve to special hose (with thimble) to add refrigerant. Tighten thimble head,
discharge air in the hose, and then stand the refrigerant bottle upside down and open bottle valve,
liquid refrigerant will flow into high pressure side of air conditioner. When pressure in bottle is no
longer larger than that in system, refrigerant will stop to flow into system. Heat the bottle with warm
water to promote pressure in bottle, and then liquid refrigerant continues to flow into system. The
whole operation process is conducted when compressor is switched off.

High pressure filling method shall be used to fill relatively large air conditioner or air conditioner by
using liquid reservoir. To control refrigerant filling volume, usually a weighing appliance will be used.
If no weighing appliance is available, refrigerant volume shall be controlled based on experience. For
the equipment without reservoir or requiring accurate filling volume, we can connect filling appliance
with low pressure valve, add or release part of refrigerant by using the same steps as the said low
pressure valve filling method.

⑶

Determination of refrigerant volume

At present, R22 refrigerant is commonly used in household air conditioner. According to the thermal
feature, under normal work condition of air conditioner, volume of refrigerant shall be calculated as
per following parameters:

①

Low pressure: evaporate pressure shall close to pressure on return gas tube of compressor which is

0.5MPa(absolute pressure 0.6MPa), and the evaporate temperature is 5

℃

;

②

Return gas temperature: temperature on the return gas tube of compressor shall be within 7

℃

~15

℃

, condensate instead of frost can occur on the return gas tube;

③

Running current: Generally running current of compressor shall not exceed rated value on the

nameplate;

④

Indoor unit air inlet and outlet temperature difference: In cooling operation, temperature difference

«
...
197
198
199
200
201
...
»

Содержание E Series

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для E Series

Бренд: Zibro Страницы: 2

Бренд: AiroDoctor Страницы: 8

Бренд: Mesa Living Страницы: 37

AIRCO BLIZZARD 1000

Бренд: WTA Страницы: 14

Бренд: Dunham-Bush Страницы: 29

Бренд: INVENTOR Страницы: 136

Бренд: Orbegozo Страницы: 143

Бренд: Lennox Страницы: 32

OTEC IEFC-D Series

Бренд: Omega Страницы: 12

Бренд: Vintage Air Страницы: 42

Бренд: Sinclair Страницы: 38

Depuro Plus 230

Бренд: Vortice Страницы: 72

Бренд: TCL Страницы: 40

Ultra Heat GMV Multi VRF Series

Бренд: Gree Страницы: 64

Бренд: Rheem Страницы: 60

Бренд: MasterCool Страницы: 2

OilonCooling Cs4

Бренд: Oilon Страницы: 29

Бренд: Daikin Страницы: 501

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды