AUMA SA 07.2-UW Скачать руководство пользователя

Страница: 31 / 76

6.1.2.

Actuator operation from remote

Risk of immediate actuator operation when switching on!

Risk of personal injuries or damage to the valve

→

If the actuator starts unexpectedly: Immediately turn selector switch to 0 (OFF).

→

Check input signals and functions.

→

Set selector switch to position Remote control (REMOTE).

Information

For actuators equipped with a positioner, it is possible to change over between OPEN
- CLOSE control (Remote OPEN-CLOSE) and setpoint control (Remote SET-
POINT). For further information, please refer to the Manual (Operation and setting).

6.2.

Menu navigation via push buttons (for settings and indications)

Menu navigation for display and setting is made via the push buttons [1 – 4] of the
local controls.

Set the selector switch [5] to position 0 (OFF) when navigating through the menu.

The bottom row of the display [6] serves as navigation support and explains which
push buttons [1 – 4] are used for menu navigation.

Figure 28:

[1–4] Push buttons or navigation support

[5]

Selector switch

[6]

Display

SA 07.2-UW – SA 16.2-UW / SAR 07.2-UW – SAR 16.2-UW Control unit: electronic (MWG)
AC 01.2 Non-Intrusive Profinet

Operation

Содержание SA 07.2-UW













































































Результаты поиска

Содержание SA 07.2-UW

Отзывы:

Похожие инструкции для SA 07.2-UW

Бренды по названию

Популярные бренды

AUMA SA 07.2-UW, Руководство по эксплуатации

Результаты поиска

Содержание SA 07.2-UW

Отзывы:

Похожие инструкции для SA 07.2-UW

Бренды по названию

Популярные бренды