AUMA SA 07.2-UW страница 27 Скачать руководство пользователя

Страница: 27 / 76

Table 19:

Explanation

Status

NETS (Network Status)

Absence of power supply or no connection to IO
controller

Offline

Red LED: off +
Green LED: off

Connection to IO controller available

RUN

Green LED: illuminated

Connection to IO controller available. However, IO
controller is in STOP status or IO data is incorrect.

STOP

Green LED: 1 brief pulse

Is used by engineering tools to identify the device
within the Profinet network

Blink

Green LED: blinking

Internal error, combined with “MODS” LED.

Fatal Event

Red LED: illuminated

Device name (station name) not yet set

Station Name Er-
ror

Red LED: 1 brief pulse

IP address not yet set

IP address Error

Red LED: 2 brief pulses

Identification incorrect

Configuration Er-
ror

Red LED: 3 brief pulses

Table 20:

Explanation

LINK/ACT1, LINK/ACT2
(Link/Activity Port 1 / 2)

No communication at port 1 or 2

Red LED: off +
Green LED: off

Port 1 or 2 are in “Link Established” status

Green LED: illuminated

Data communication via port 1 or port 2

Green LED: blinking

No function

Red LED

Description of LEDs on base sub-assembly

Table 21:

Explanation

LED

No Reset active, power supply available

RESET LED: illuminated

Sub-assembly in Reset status
Sub-assembly in initialisation status
Debug mode active
Normal status (Profinet application active)

DEBUG LED: illuminated
DEBUG LED: 1 brief pulse
DEBUG LED: briefly blinking (1
Hz)
DEBUG LED: slowly blinking (5
Hz)

Error of internal CAN communication

CAN LED: illuminated

Bus active ("Link Established" at port 1 or port 2)

BA1 LED or BA2 LED: illumin-
ated

“Data Exchange” via Profinet

DX LED: illuminated

SA 07.2-UW – SA 16.2-UW / SAR 07.2-UW – SAR 16.2-UW Control unit: electronic (MWG)
AC 01.2 Non-Intrusive Profinet

Electrical connection

Содержание SA 07.2-UW













































































Результаты поиска

Содержание SA 07.2-UW

Отзывы:

Похожие инструкции для SA 07.2-UW

Бренды по названию

Популярные бренды

AUMA SA 07.2-UW, Руководство по эксплуатации

Результаты поиска

Содержание SA 07.2-UW

Отзывы:

Похожие инструкции для SA 07.2-UW

Бренды по названию

Популярные бренды