AUMA SA 07.2-UW Скачать руководство пользователя

Страница: 24 / 76

5.3.4.

Fieldbus terminal compartment: open

Figure 21: Open cover to fieldbus terminal compartment

[1]

Cover (fieldbus terminal compartment)

[2]

Screws for cover

[3]

O-ring

[4]

Cable entries for fieldbus cables

[5]

Blanking plug

Electric shock due to presence of hazardous voltage!

Failure to observe this warning results in death or serious injury.

→

Disconnect device from the mains before opening.

Electrostatic discharge ESD!

Risk of damage to electronic components.

→

Earth both operators and devices.

Loosen screws [2] and remove cover [1].

Insert cable glands suitable for fieldbus cables.

➥

The enclosure protection IP… stated on the name plate is only ensured if suit-

able cable glands are used.

Figure 22: Example: Name plate for enclosure protection IP68

Seal unused cable entries with suitable plugs.

SA 07.2-UW – SA 16.2-UW / SAR 07.2-UW – SAR 16.2-UW Control unit: electronic (MWG)

Electrical connection

AC 01.2 Non-Intrusive Profinet

Содержание SA 07.2-UW













































































Результаты поиска

Содержание SA 07.2-UW

Отзывы:

Похожие инструкции для SA 07.2-UW

Бренды по названию

Популярные бренды

AUMA SA 07.2-UW, Руководство по эксплуатации

Результаты поиска

Содержание SA 07.2-UW

Отзывы:

Похожие инструкции для SA 07.2-UW

Бренды по названию

Популярные бренды