AUMA SA 07.2-UW Скачать руководство пользователя

Страница: 47 / 76

CLOSE or OPEN

Use

Up ▲ Down ▼

to select:

→

▶ Trip torque CLOSE

→

▶ Trip torque OPEN

➥

The black triangle

▶

indicates the current selection.

Press

➥

Display shows the set value.

➥

The bottom row indicates:

Edit Esc

Press

Edit

➥

Display indicates:

Specialist (4) →

continue with step 7

in bottom row

Up ▲ Down ▼ Esc →

continue with step 11

User login

Use

Up ▲ Down ▼

to select user:

Information: Required user level:

Specialist (4)

or higher.

➥

The symbols have the following meanings:

black triangle:

▶

= current setting

white triangle:

▷

= selection (not saved yet)

Press

➥

Display indicates:

Password 0***

Enter password (

→

enter password).

➥

Display shows the set value.

➥

The bottom row indicates:

Edit Esc

10.

Press

Edit

Change value

11. Enter new value for tripping torque via

Up ▲ Down ▼

Information: The adjustable torque range is shown in round brackets.

12. Save new value via

Save

➥

The tripping torque is set.

13. Back to step 4 (CLOSED or OPEN): Press

Esc

Information

The following fault signals are issued if the torque setting performed has been reached
in mid-travel:

●

In the display of the local controls: Status indication

S0007 Fault

Torque fault OPEN

Torque fault CLOSE

The fault has to be acknowledged before the operation can be resumed. The
acknowledgement is made:

either by an operation command in the opposite direction.
-

For

Torque fault OPEN

: Operation command in direction CLOSE

For

Torque fault CLOSE

: Operation command in direction OPEN

or, in case the torque applied is lower than the preset tripping torque:
-

in selector switch position Local control (LOCAL) via push button RESET.

in selector switch position Remote control (REMOTE):
-

via the fieldbus, command reset., if the fieldbus is the active command
source.

via a digital input (I/O interface) with RESET command if a digital input
is configured for signal

RESET

and the I/O interface is the active

command source.

SA 07.2-UW – SA 16.2-UW / SAR 07.2-UW – SAR 16.2-UW Control unit: electronic (MWG)
AC 01.2 Non-Intrusive Profinet

Commissioning (basic settings)

Содержание SA 07.2-UW













































































Результаты поиска

Содержание SA 07.2-UW

Отзывы:

Похожие инструкции для SA 07.2-UW

Бренды по названию

Популярные бренды

AUMA SA 07.2-UW, Руководство по эксплуатации

Результаты поиска

Содержание SA 07.2-UW

Отзывы:

Похожие инструкции для SA 07.2-UW

Бренды по названию

Популярные бренды