ASP STERRAD 100S Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 44

background image

Routine

Maintenance

3

STERRAD

®

Sterilization System Routine Maintenance Guide

33

Figure 18. Placing a new paper roll into the retaining slots.

4. Insert the new paper roll so that the paper feeds from the back of the

roll. Set the rod in the metal retaining clips.

5. Make sure the paper is smooth and the edge is cut clean.

6. Feed the edge of the paper into the slot behind the printer ribbon

until firm resistance is felt. Push up gently on the paper and press

PAPER ADVANCE

until the mechanism begins to pull the paper.

Continue pressing

PAPER ADVANCE

until about 70 to 80 mm (3

inches) of paper exits the slot above.

Figure 19. Feeding the paper into the mechanism.

7. Close the printer drawer, taking care to ensure the paper exits the

printer paper slot.

To replace the

double roll printer paper,

do the following:

Note

: Do not pull the remaining paper out of the printer

mechanism. Instead cut or tear the paper and then
press

PAPER ADVANCE

to remove the paper

from the printer. This prevents any paper debris
from interring with the advance mechanism.

1. Open the printer drawer on the control panel and remove the large

take-up reel containing the yellow backup copies of the cycles.

«
...
31
32
33
34
35
...
»

Содержание STERRAD 100S













































Отзывы:

Нет отзывов

Похожие инструкции для STERRAD 100S

FX-ARM CONTROLLER

Бренд: Magicfx Страницы: 16

Бренд: Zetec Страницы: 23

Бренд: Cameo Страницы: 64

Бренд: Cameo Страницы: 100

Бренд: CAME Страницы: 32

Бренд: Mandam Страницы: 9

Бренд: IDEAL Страницы: 12

Бренд: ParaBody Страницы: 3

Бренд: Valiani Страницы: 66

Бренд: Madsen Страницы: 206

Бренд: T&D Страницы: 28

Бренд: Zero88 Страницы: 26

GPSMAP 9 3 Series

Бренд: Garmin Страницы: 222

INTRA PROPHYwiz 181 P

Бренд: KaVo Страницы: 22

Бренд: Festo Страницы: 40

Бренд: Neurotech Страницы: 24

Бренд: Life Fitness Страницы: 8

Бренд: Moticon Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды