ASP STERRAD 100S Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 44

background image

3

Routine Maintenance

32

STERRAD

®

Sterilization System Routine Maintenance Guide

5. Turn the knob on the cartridge clockwise to remove any slack from

the ribbon.

Figure 15. Removing slack from the printer ribbon.

6. Close the printer drawer, taking care to ensure that the printer paper

exits the printer paper slot.

Figure 16. Closing the printer drawer.

Replacing the Printer Paper

To replace the

single roll printer paper,

do the following:

1. Open the printer drawer on the control panel.

Figure 17. Opening the printer drawer.

(Early version of STERRAD System shown.)

2. Remove the metal rod from the empty paper core and discard the

core.

3. Insert the rod into the core of the new paper roll.

«
...
30
31
32
33
34
...
»

Содержание STERRAD 100S













































Отзывы:

Нет отзывов

Похожие инструкции для STERRAD 100S

Бренд: Keithley Страницы: 67

Бренд: Keithley Страницы: 23

Бренд: Keithley Страницы: 93

Бренд: Oki Страницы: 44

Бренд: Magnescale Страницы: 64

Бренд: Ultimaker Страницы: 38

Бренд: A&D Страницы: 2

Бренд: A&D Страницы: 176

Бренд: JB Systems Страницы: 12

Бренд: NANLUX Страницы: 39

Бренд: Farmi Forest Corporation Страницы: 32

Бренд: idi Страницы: 20

Бренд: G&G Страницы: 2

Бренд: H&S Страницы: 46

Бренд: JBSYSTEMS Light Страницы: 17

Бренд: ZOLL Страницы: 37

Бренд: Wagan Страницы: 4

Бренд: Wachs Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды