ASP STERRAD 100S Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 44

ASP STERRAD 100S Скачать руководство пользователя страница 18

3

Routine Maintenance

18

STERRAD

®

Sterilization System Routine Maintenance Guide

PM Main Menu

Enter the deep edit mode as shown in Module 6.

PM WARNING = ON (or) OFF OPEN(chng)-
CANCEL(next)

ON or OFF indicates the state of the Planned Maintenance warning
feature. When this feature has been turned OFF, no messages related to
performing planned maintenance are generated. Press OPEN DOOR to
toggle the warning between ON and OFF. Press CANCEL to accept the
choice displayed.

If the warning feature is ON, pressing CANCEL gives different options
for selecting the PM interval. If this feature is OFF, pressing CANCEL
transfers you to the Serial Number Edit Menu.

The PM warning is set to ON by default, whenever a loss of battery
power occurs, or the number of total machine cycle is reset to zero.

PM Level 1 (2) Edit Menu

The following is displayed:

PM Y (or) N; NEXT PM = XXXX L(X)
OPEN(reset)-CANCEL(next)

Y is yes PM was done. N is no PM has not been done. XXXX is the
number of cycles before the PM is due, or the month in which the PM is
due and L(X) is level 1 or level 2. If PM is not due on the basis of either
months or cycles, XXXX is in cycles. If both months and cycles are due,
or both are past due, XXXX is also in cycles. XXXX is displayed in
months, if months are due, and cycles are not due. Months are also
displayed if months are past due, while cycles are less than past due. If
the number shown is a negative number, then it is the number of cycles
past due.

«
...
16
17
18
19
20
...
»

Содержание STERRAD 100S













































Отзывы:

Нет отзывов