ASP STERRAD 100S Скачать руководство пользователя | Manualshive

Страница: 29 / 44

background image

Routine

Maintenance

3

STERRAD

®

Sterilization System Routine Maintenance Guide

29

2. Reach into the sterilizer and grasp the protruding end of the

vaporizer plate that is closest to you. Pull firmly on the plate;
outward and downward so that the lips of the plate unhook from the
electrode. You may also want to squeeze the plate slightly and move
it outward and downward. Remove the plate from the sterilizer and
discard it according to hospital policy.

Installing a New Vaporizer Plate

CAUTION: Please make sure you follow the steps

below and hold the vaporizer plate as shown
in the illustration. It is very important that
the vaporizer plate be correctly installed so
that it functions properly.

WARNING! YOU MUST WEAR EYE PROTECTION AND

GLOVES WHILE PERFORMING THIS
PROCEDURE.

1. Remove the vaporizer plate from its packaging. Hold the plate and

insert it as shown in the following figures.

Figure 7. There are two ways to hold the plate for insertion.

Choose the one that is most comfortable for you.

Figure 8. Insert the plate from either side of the opening. The plate fits snugly.

«
...
27
28
29
30
31
...
»

Содержание STERRAD 100S













































Отзывы:

Нет отзывов

Похожие инструкции для STERRAD 100S

Бренд: Obdstar Страницы: 10

Бренд: Raymarine Страницы: 124

Бренд: Raymarine Страницы: 192

Бренд: Balanced Body Страницы: 4

Бренд: Balanced Body Страницы: 2

Reformer Trapeze Combination

Бренд: Balanced Body Страницы: 164

Бренд: Balanced Body Страницы: 37

QUICK-ALIGN Vari-Flex

Бренд: Össur Страницы: 36

Бренд: Össur Страницы: 2

Бренд: Össur Страницы: 8

Exitronix LEMD Series

Бренд: BARRON Страницы: 6

Бренд: Daekyung Страницы: 15

Team Agile Color Tune TM16-0

Бренд: GRAU Страницы: 24

Бренд: Raytec Страницы: 8

Бренд: impact Страницы: 8

Бренд: TOTAL10 Страницы: 16

Бренд: TiePie Страницы: 4

Бренд: Qtx Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды