ARTERY AT32F425 Series Скачать руководство пользователя страница 277 | Manualshive

Страница: 277 / 429

background image

AT32F425

Series Reference Manual

2022.03.30

Page 277

Ver 2.01

0: Break input is disabled.
1: Break input is enabled.

Bit 11

FCSOEN

0x0

rw

Frozen channel status when holistic output enable
This bit acts on the channels that have complementary
output. It is used to set the channel state when the timer
is inactive and MOEN=1.
0: CxOUT/CxCOUT outputs are disabled.
1: CxOUT/CxCOUT outputs are enabled. Output inactive
level.

Bit 10

FCSODIS

0x0

rw

Frozen channel status when holistic output disable
This bit acts on the channels that have complementary
output. It is used to set the channel state when the timer
is inactive and MOEN=0.
0: CxOUT/CxCOUT outputs are disabled.
1: CxOUT/CxCOUT outputs are enabled. Output idle
level.

Bit 9: 8

WPC

0x0

rw

Write protection configuration
his field is used to enable write protection.
00: Write protection is OFF.
01: Write protection level 3, and the following bits are write

protected:

TMRx_BRK: DTC, BRKEN, BRKV and AOEN
TMRx_CTRL2: CxIOS and CxCIOS
10: Write protection level 2. The following bits and all bits

in leve 3 are write protected:

TMRx_CCTRL: CxP and CxCP
TMRx_BRK: FCSODIS and FCSOEN
11: Write protection level 1. The following bits and all bits

in level 2 are write protected:

TMRx_CMx: C2OCTRL and C2OBEN
Note: Once WPC>0, its content remains frozen until the
next system reset.

Bit 7: 0

DTC

0x00

rw

Dead-time configuration
This field defines the duration of the dead-time insertation.
The 3-bit MSB of DTC[7: 0] is used for function
selection:
0xx: DT = DTC [7

：

0] * TDTS

10x: DT = (64+ DTC [5: 0]) * TDTS * 2
110: DT = (32+ DTC [4: 0]) * TDTS * 8
111: DT = (32+ DTC [4: 0]) * TDTS * 16

Note: Based on lock configuration, AOEN, BRKV, BRKEN, FCSODIS, FCSOEN and DTC[7:0] can all

be write protected. Thus it is necessary to configure write protection when writing to the
TMRx_BRK register for the first time.

14.6.4.19

TMR1 DMA control register (TMR1_DMACTRL)

Bit

Register

Reset value

Type

Description

Bit 15:13

Reserved

0x0

resd

Kept at its default value.

Bit 12:8

DTB

0x00

rw

DMA transfer bytes
This field defines the number of DMA transfers:
00000: 1 byte              00001: 2 bytes
00010: 3 bytes              00011: 4 bytes
......                                      ......
10000: 17 bytes          10001: 18 bytes

Bit 7:5

Reserved

0x0

resd

Kept at its default value.

Bit 4: 0

ADDR

0x00

rw

DMA transfer address offset
ADDR is defined as an offset starting from the address of
the TMRx_CTRL1 register:
00000: TMRx_CTRL1
00001: TMRx_CTRL2
00010: TMRx_STCTRL
......

«
...
275
276
277
278
279
...
»

Содержание AT32F425 Series














































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AT32F425 Series

LS42 - BladeCenter - 7902

Бренд: IBM Страницы: 56

Бренд: IBM Страницы: 2

BladeCenter Management Module

Бренд: IBM Страницы: 78

Бренд: IBM Страницы: 110

Remote Supervisor Adapter II

Бренд: IBM Страницы: 132

Бренд: Laird Страницы: 36

RDX QuikStation 4

Бренд: Tandberg Data Страницы: 2

Бренд: Alcad Страницы: 6

Бренд: Ruckus Wireless Страницы: 56

Бренд: Renesas Страницы: 6

Бренд: Alesis Страницы: 61

Бренд: FONESTAR Страницы: 8

Бренд: Moxa Technologies Страницы: 2

Бренд: netsys Страницы: 164

Бренд: Spirent Страницы: 22

Бренд: Digi Страницы: 75

Ultra WiFi Booster

Бренд: Optus Страницы: 8

Бренд: A.E.B. Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды