manualshive.com logo in svg

ARTERY AT32F425 Series, Справочное руководство

Поделиться
Скачать
ARTERY AT32F425 Series Скачать руководство пользователя страница 336

  AT32F425

 

Series  Reference  Manual

 

2022.03.30

 

Page 336 

 

Ver 2.01

 

in the FIFO 0. 
RF0ML  bit  is  incremented  by  one  each  time  a  new 
message has been received and passed the fitler while the 
FIFO 0 is not full.

 

RF0ML bit is decremented by one each time the software 
releases the receive FIFO 0 by writing 1 to the RF0R bit.

 

19.7.1.5  CAN receive FIFO 1 register (CAN_RF1) 

Bit 

Register 

Reset value 

Type 

Description 

Bit 31: 6 

Reserved 

0x0000000 

resd 

Kept at its default value. 

Bit 5 

RF1R 

0x0 

rw1s 

Receive FIFO 1 release 
0: No effect 
1: Release FIFO   
Note: 
This bit is set by software to release FIFO 1. It is cleared 
by hardware when the FIFO 1 is released. 
Seting this bit by software has no effect when the FIFO 1 
is empty. 
If there are more than two messages pending in the FIFO 
0, the software has to release the FIFO  1 to access the 
second message.

 

Bit 4 

RF1OF 

0x0 

rw1c 

Receive FIFO 1 overflow flag 
0: No overflow 
1: Receive FIFO 1 overflow 
Note: 
This bit is set by hardware when a new message has been 
received and passed the filter while the FIFO 1 is full. 
It is cleared by software by writing 1.

 

Bit 3 

RF1FF 

0x0 

rw1c 

Receive FIFO 1 full flag 
0: Receive FIFO 1 is not full 
1: Receive FIFO 1 is full 
Note: 
This  bit  is  set  by  hardware  when  three  messages  are 
pending in the FIFO 1. 
It is cleared by software by writing 1.

 

Bit 2 

Reserved 

0x0 

resd 

Kept at its default value. 

Bit 1: 0 

RF1MN 

0x0 

ro 

Receive FIFO 1 message num 
Note: 
These two bits indicate how many messages are pending 
in the FIFO 1. 
RF1ML  bit  is  incremented  by  one  each  time  a  new 
message has been received and passed the fitler while the 
FIFO 1 is not full.

 

RF1ML bit is decremented by one each time the software 
releases the receive FIFO 1 by writing 1 to the RF1R bit.

 

19.7.1.6  CAN interrupt enable register (CAN_INTEN) 

Bit 

Register 

Reset value 

Type 

Description 

Bit 31: 18  Reserved 

0x0000 

resd 

Kept at its default value. 

Bit 17 

EDZIEN 

0x0 

rw 

Enter doze mode interrupt enable 
0: Enter sleep mode interrupt disabled 
1: Enter sleep mode interrupt enabled 
Note:  EDZIF  flag  bit  corresponds  to  this  interrupt.  An 
interrupt is generated when both this bit and EDZIF bit are 
set. 

Bit 16 

QDZIEN 

0x0 

rw 

Quit doze mode interrupt enable 
0: Quit sleep mode interrupt disabled 
1: Quit sleep mode interrupt enabled 
Note:  The  flag  bit  of  this  interrupt  is  the  QDZIF  bit. An 
interrupt is generated when both this bit and QDZIF bit are 
set. 

Bit 15 

EOIEN 

0x0 

rw 

Error occur interrupt enable 
0: Error interrupt disabled 

Содержание AT32F425 Series














































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды