ARTERY AT32F425 Series Скачать руководство пользователя страница 396 | Manualshive

Страница: 396 / 429

background image

AT32F425

Series Reference Manual

2022.03.30

Page 396

Ver 2.01

1: Low-power mode

Bit 16

PWRDOWN

0x0

rw

Power down
This bit is used to activate the transceiver in
transmission/reception. It must be pre-configured to allow
USB communication.
0: Power down enable
1: Power down disable (Transceiver active)

Bit 15: 0

Reserved

0x0000

resd

Kept at its default value.

20.6.3.13

OTGFS controller ID register (OTGFS_GUID)

This is a read-only register containg the production ID.

Bit

Register

Reset value

Type

Description

31: 0

USERID

0x0000 1000 rw

Product ID field
The application can program the ID field.

20.6.3.14

OTGFS host periodic Tx FIFO size register

(OTGFS_HPTXFSIZ)

This register contains the size and memory start address of the periodic transmit FIFO.

Bit

Register

Reset value

Type

Description

Bit 31: 16 PTXFSIZE

0x02000

ro/rw

Host periodic TxFIFO depth
Values are in terms of 32-bit words.
Minimum value is 16
Maximum value is 512

Bit 15: 0

PTXFSTADDR

0x0600

ro/rw

Host Periodic TxFIFO start address
The power-on reset value of this register is the sum of the
largest receive FIFO depth and the largest non-periodic
transmit FIFO depth.

20.6.3.15

OTGFS device IN endpoint Tx FIFO size register

(OTGFS_DIEPTXFn) (x=1

…

7, where n is the FIFO number)

This register holds the depth and memory start address of the IN endpoint transmit FIFO in device mode.
Each of the FIFOs contains an IN endpoint data. This register can be used repeatedly for instantiated
IN endpoint FIFO1~15 . The GNPTXFSIZ register is used to program the depth and memory start
address of the IN endpoint FIFO 0.

Bit

Register

Reset value

Type

Description

Bit 31: 16 INEPTXFDEP

0x0200

ro/rw

IN Endpoint TxFIFO depth
Values are in terms of 32-bit words.
Minimum value is 16
Maximum value is 512
The reset value is the maximum possible IN endpoint
transmit FIFO depth

Bit 15: 0

INEPTXFSTADDR

0x0400

ro/rw

IN Endpoint FIFOn transmit SRAM start address
This field contains the SRAM start address of the IN
endpoint n transmit FIFO

20.6.4 Host-mode registers

Host-mode registers affect the operation of the controller in host mode. Host-mode register are not
accessible in device mode (as the results are undefined in device mode). Host-mode registers contain
as follows:

20.6.4.1 OTGFS host mode configuration register (OTGFS_HCFG)

This register is used to configure the controller after power-on. Do not change this register after
initialization.

Bit

Register

Reset value

Type

Description

Bit 31: 3

Reserved

0x0000 0000 resd

Kept at its default value.

Bit 2

FSLSSUPP

0x0

ro

FS- and LS-only support
The application uses this bit to control the controller’s
enumeration speed. With this bit, the application can make
the controller enumerate as a full-speed host mode, even

«
...
394
395
396
397
398
...
»

Содержание AT32F425 Series














































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AT32F425 Series

C50FSi - VB Network Camera

Бренд: Canon Страницы: 32

Бренд: Rabbit Страницы: 120

Бренд: XMG Страницы: 5

Бренд: NAD Страницы: 2

ILDA Gem Laser projector tool

Бренд: Stanwax Laser Страницы: 3

Бренд: ForeScout Страницы: 28

Бренд: Klark Teknik Страницы: 50

iTRON B 70.2040

Бренд: JUMO Страницы: 41

DL-DVI-Vision-IP Series

Бренд: G&D Страницы: 228

CY62136EV30 MoBL

Бренд: Cypress Semiconductor Страницы: 12

PFC Chokes PFC3515V Series

Бренд: Delta Electronics Страницы: 1

Бренд: PaloAlto Networks Страницы: 28

Бренд: Cypress Semiconductor Страницы: 26

Бренд: Kontron Страницы: 14

Бренд: Abocom Страницы: 70

Бренд: ICP DAS USA Страницы: 62

Linktropy MINI-G

Бренд: Apposite Technologies Страницы: 57

Бренд: Corsair Страницы: 134

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды