Arctic Cat 1000 XT 2014 Скачать руководство пользователя страница 70

Страница: 70 / 151

GZ442

2. Remove the snap ring securing the bearing in the

water pump drive cover; then remove the bearing
using an appropriate blind bearing remover.

GZ441

Inspecting

1. Inspect the water pump drive housing (A) for scoring

or discoloration.

GZ440A

2. Inspect the bearing (B) for smooth rotation and no dis-

coloration or scoring.

3. Inspect the gear (C) for chipped or missing teeth, exces-

sive hub wear, or excessive wear in the drive pin slot.

4. Inspect the drive pin (D) and driveshaft (E) for exces-

sive wear or looseness.

Assembling

1. Install the bearing in the water pump drive cover and

secure with the snap ring (flat side away from the bearing).

GZ441

2. Install the gear onto the driveshaft noting correct ori-

entation (from step 1 of disassembling).

GZ442

3. Install the two snap rings on the driveshaft (flat side

away from the gear).

Installing Right-Side

Components

1. Apply silicone to the mating surfaces; then install the

gear position switch making sure the two contact
pins and springs are properly positioned. Tighten the
cap screws securely.

CD997

Содержание 1000 XT 2014
























































































































































Результаты поиска

Содержание 1000 XT 2014

Отзывы:

Похожие инструкции для 1000 XT 2014

Бренды по названию

Популярные бренды

Arctic Cat 1000 XT 2014, Руководство по обслуживанию

Результаты поиска

Содержание 1000 XT 2014

Отзывы:

Похожие инструкции для 1000 XT 2014

Бренды по названию

Популярные бренды