Arctic Cat 1000 XT 2014 Скачать руководство пользователя страница 44

Страница: 44 / 151

GZ026



NOTE: Timing marks on the rotor/flywheel are

stamped with an “F” (front cylinder) and “R” (rear cyl-
inder) adjacent to the mark.

GZ063

GZ059

2. Remove the tappet covers on the cylinder being ser-

viced. The tappets should not have pressure on them.

3. Loosen the cap screws securing the valve cover to

the head.

GZ126A

4. Remove all cap screws except the two top-side cap

screws next to the spark plug. These will keep the
alignment pins in place. Note the two rubber washers
on the remaining cap screws.

5. Remove the valve cover. Account for and note the

orientation of the cylinder head plug. Note the loca-
tion of the two alignment pins.

GZ162

GZ132A

6. Remove the cap screw on the end of the tensioner;

then using a flat-blade screwdriver, turn the tensioner
clockwise to remove the tension. Remove the two
cap screws securing the tensioner adjuster assembly
and remove the assembly. Account for a gasket.

Содержание 1000 XT 2014
























































































































































Результаты поиска

Содержание 1000 XT 2014

Отзывы:

Похожие инструкции для 1000 XT 2014

Бренды по названию

Популярные бренды

Arctic Cat 1000 XT 2014, Руководство по обслуживанию

Результаты поиска

Содержание 1000 XT 2014

Отзывы:

Похожие инструкции для 1000 XT 2014

Бренды по названию

Популярные бренды