Arctic Cat 1000 XT 2014 Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 151

background image

45

16. Using an awl, remove one piston-pin circlip.

GZ145

17. Using the Piston Pin Puller, remove the piston pin.

Account for the opposite-side circlip. Remove the pis-

ton.



NOTE: It is advisable to remove the opposite-side

circlip prior to using the puller.



NOTE: Support the connecting rod with rubber

bands or a piece of hose to avoid damaging the rod
or install a suitable connecting rod holder.

GZ146A

Servicing Top-Side

Components

VALVE ASSEMBLY

When servicing valve assembly, inspect valve seats, valve

stems, valve faces, and valve stem ends for pits, burn
marks, or other signs of abnormal wear.



NOTE: Whenever a valve is out of tolerance, it must

be replaced.

Cleaning/Inspecting Valve Cover



NOTE: If the valve cover cannot be trued, the cylin-

der head assembly must be replaced.

1. Wash the valve cover in parts-cleaning solvent.

2. Place the valve cover on the Surface Plate covered

with #400 grit wet-or-dry sandpaper. Using light pres-
sure, move the valve cover in a figure eight motion.
Inspect the sealing surface for any indication of high
spots. A high spot can be noted by a bright metallic
finish. Correct any high spots before assembly by con-
tinuing to move the valve cover in a figure eight
motion until a uniform bright metallic finish is
attained.

CC130D

Removing Valves



NOTE: Index all valves, springs, and cotters to their

original position when removing. When installing, all
valve components should be installed in their origi-
nal position.

1. Using a valve spring compressor, compress the valve

springs and remove the valve cotters. Account for an
upper spring retainer.



AT THIS POINT

To service cylinder, see Servicing Top-Side Compo-

nents sub-section.

CAUTION

When removing the cylinder, be sure to support the pis-

ton to prevent damage to the crankcase and piston.

CAUTION

Do not allow the connecting rod to go down inside the
crankcase. If the rod is down inside the crankcase and
the crankshaft is rotated, severe damage will result.



AT THIS POINT

To service piston, see Servicing Top-Side Components

sub-section.



AT THIS POINT

To service center crankcase components only, proceed

to Removing Left-Side Components.

CAUTION

Do not remove an excessive amount of the sealing sur-
face or damage to the camshaft will result. Always
check camshaft clearance when resurfacing the valve
cover.

CAUTION

Water or parts-cleaning solvent must be used in con-

junction with the wet-or-dry sandpaper or damage to
the sealing surface may result.

«
...
45
46
47
48
49
...
»

Содержание 1000 XT 2014
























































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1000 XT 2014

Бренд: J&M Страницы: 25

Бренд: ADLY MOTO Страницы: 42

Бренд: Polaris Страницы: 174

BLADE 1000 EPS IRS 4X4

Бренд: TGB Страницы: 16

Бренд: KMW Страницы: 51

Honey Joy TY324116

Бренд: Costway Страницы: 7

Бренд: ACG Страницы: 97

Бренд: E-TON Страницы: 38

Бренд: Taylor-Dunn Страницы: 180

Бренд: Kellfri Страницы: 8

Бренд: Access Motor Страницы: 65

Бренд: KAYO MOTO Страницы: 6

Бренд: Sauber Страницы: 11

Бренд: Massimo Страницы: 220

Бренд: Joyner Страницы: 77

CYCLONE 56380676

Бренд: Nilfisk-Advance Страницы: 36

City Ranger 3500

Бренд: Nilfisk-Advance Страницы: 68

Sure-Trac ST6008

Бренд: Novae Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды