Arctic Cat 1000 XT 2014 Скачать руководство пользователя страница 67

Страница: 67 / 151

GZ251

15. Using Seal Protector Tool, install the outer magneto

cover using a new gasket and secure with the cap
screws. Using the pattern shown, tighten to 112 in.-lb.

GZ212B

Right-Side Components



NOTE: For efficiency, it is preferable to remove and

disassemble only those components which need to be
addressed and to service only those components. The
technician should use discretion and sound judgment.



NOTE: The engine/transmission does not have to

be removed from the frame for this procedure.

Removing Right-Side

Components

A. CVT Cover
B. Driven Clutch
C. Clutch Cover
D. Centrifugal Clutch

1. Remove the cap screws securing the CVT cover; then using

a rubber mallet, gently tap on the cover tabs to loosen the
cover. Account for a gasket and two alignment pins.

GZ244B

2. Remove the nut securing the movable drive face; then

remove the face. Account for a spacer and a flat
washer.

GZ074

CD966A

3. Remove the V-belt.

4. Remove the nut securing the fixed driven assembly;

then remove the assembly.



AT THIS POINT

To service any one specific component, only limited dis-

assembly of components may be necessary. Note the
AT THIS POINT information in each sub-section.

Содержание 1000 XT 2014
























































































































































Результаты поиска

Содержание 1000 XT 2014

Отзывы:

Похожие инструкции для 1000 XT 2014

Бренды по названию

Популярные бренды

Arctic Cat 1000 XT 2014, Руководство по обслуживанию

Результаты поиска

Содержание 1000 XT 2014

Отзывы:

Похожие инструкции для 1000 XT 2014

Бренды по названию

Популярные бренды