Arctic Cat 1000 XT 2014 Скачать руководство пользователя страница 69

Страница: 69 / 151

11. Carefully remove the existing clutch housing seal

using caution not to damage the sealing surface of
the cover.

GZ513

12. Remove the one-way clutch from the centrifugal

clutch. Note the location of the green dot (or the
word OUTSIDE) for installing purposes.

13. Remove the nut (left-hand threads) securing the clutch

shoe assembly.

GZ438A



NOTE: Heating the nut will aid in removal.

14. Remove the two cap screws securing the gear posi-

tion switch; then remove the switch. Account for two
contact pins and two springs.

CD997

15. Remove the water pump drive housings. Account for a

gasket and two locator pins.

GZ437A

16. Remove the water pump drive shaft and gear assem-

bly from the engine.

GZ439

Servicing Right-Side

Components

INSPECTING CENTRIFUGAL CLUTCH
SHOES

1. Inspect the clutch shoes for wear, chips, cracks, dam-

age, or discoloration. If any shoe is damaged, replace
the centrifugal clutch.

INSPECTING CLUTCH HOUSING

1. Inspect the clutch housing for burns, grooving, cracks,

or uneven wear.

2. If the housing is damaged in any way, the housing

must be replaced.

DRIVEN CLUTCH ASSEMBLY



NOTE: The driven clutch is a non-serviceable com-

ponent. If the clutch faces, cam ramps, or face bush-
ing are worn or loose, the clutch must be replaced as
an assembly. Do not disassemble the driven clutch.

WATER PUMP DRIVE ASSEMBLY
Disassembling

1. Remove the two snap rings from the driveshaft; then

remove the gear and drive pin noting the orientation of
the gear for proper assembly.

Содержание 1000 XT 2014
























































































































































Результаты поиска

Содержание 1000 XT 2014

Отзывы:

Похожие инструкции для 1000 XT 2014

Бренды по названию

Популярные бренды

Arctic Cat 1000 XT 2014, Руководство по обслуживанию

Результаты поиска

Содержание 1000 XT 2014

Отзывы:

Похожие инструкции для 1000 XT 2014

Бренды по названию

Популярные бренды