Arctic Cat 1000 XT 2014 Скачать руководство пользователя страница 98

Страница: 98 / 151

KX190

3. Rotate the fuel pump until the match marks align;

then install the mounting screws and tighten securely
using a crisscross pattern.



NOTE: It is important to install the fuel pump with

the correct orientation to ensure adequate float lever
clearance.

4. Connect the wires, fuel hose, and spring clamp; then

turn the ignition switch to the ON position. Note that
the fuel pump runs momentarily and the fuel gauge
indicates the proper fuel level.

5. With the transmission in neutral and brake lever lock

engaged, start the engine and check for normal oper-
ation. Check for any fuel leaks.

6. Install any wire ties that were removed; then install

the rear fenders, rack, and seat making sure the seat
locks securely.

Troubleshooting

Problem: Starting impaired

Condition

Remedy

Gas

contaminated

1. Drain gas tank and fill with clean gas

Problem: Idling or low speed impaired

Condition

Remedy

TPS

out of adjustment

1. Adjust TPS

Problem: Medium or high speed impaired

Condition

Remedy

High RPM “cut out”

against RPM limiter

1. Decrease RPM speed

Содержание 1000 XT 2014
























































































































































Результаты поиска

Содержание 1000 XT 2014

Отзывы:

Похожие инструкции для 1000 XT 2014

Бренды по названию

Популярные бренды

Arctic Cat 1000 XT 2014, Руководство по обслуживанию

Результаты поиска

Содержание 1000 XT 2014

Отзывы:

Похожие инструкции для 1000 XT 2014

Бренды по названию

Популярные бренды