Arctic Cat 1000 XT 2014 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 151

background image

8

GZ063



NOTE: At this point, the rocker arms and adjuster

screws must not have pressure on them.

Feeler Gauge Procedure

A. Using a feeler gauge, check each valve/tappet

clearance. If clearance is not within specifica-
tions, loosen the jam nut and rotate the tappet
adjuster screw until the clearance is within speci-
fications. Tighten each jam nut securely after
completing the adjustment.

CC007DC

B. Rotate the engine 270° to the TDC position of the

rear cylinder; then repeat step A.

GZ059

Valve Adjuster Procedure



NOTE: The

seat,

storage

compartment

cover

assembly, compartment box, air filter/filter housing,
and

left-side/right-side

splash

panels

must

be

removed for this procedure.

A. Place Valve Clearance Adjuster onto the jam nut

securing the tappet adjuster screw; then rotate the
valve adjuster dial clockwise until the end is
seated in the tappet adjuster screw.

B. While holding the valve adjuster dial in place, use

the valve adjuster handle and loosen the jam nut;
then rotate the tappet adjuster screw clockwise
until friction is felt.

C. Align the valve adjuster handle with one of the

marks on the valve adjuster dial.

D. While holding the valve adjuster handle in place,

rotate the valve adjuster dial counterclockwise
until proper valve/tappet clearance is attained.



NOTE: Refer to the appropriate specifications in

Feeler Gauge Procedure sub-section for the proper
valve/tappet clearance.



NOTE: Rotating the valve adjuster dial counter-

clockwise will open the valve/tappet clearance by
0.05 mm (0.002 in.) per mark.

E. While holding the adjuster dial at the proper

clearance setting, tighten the jam nut securely
with the valve adjuster handle.

F. Rotate the engine 270° to the TDC position of the

rear cylinder; then repeat steps A-E for the rear
cylinder.

3. Install the timing inspection plug; then remove the

cap screw and install the crankcase end cap.

4. Place the tappet covers into position making sure the

proper cap screws are with the proper cover. Tighten
the cap screws securely.

5. Install the spark plug(s).

CAUTION

The feeler gauge must be positioned at the same angle

as the valve and valve adjuster for an accurate measure-
ment of clearance. Failure to measure the valve clear-
ance accurately could cause valve component damage.

VALVE/TAPPET CLEARANCE

1000

0.08-0.12 mm (0.003-0.005 in.) - Intake
0.13-0.17 mm (0.005-0.007 in.) - Exhaust

«
...
8
9
10
11
12
...
»

Содержание 1000 XT 2014
























































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1000 XT 2014

Бренд: Taylor-Dunn Страницы: 126

Бренд: Baja motorsports Страницы: 82

Бренд: Taylor-Dunn Страницы: 134

Бренд: Polaris Страницы: 174

Бренд: Rayco Страницы: 88

Бренд: Lenoxx Страницы: 16

POWER WHEELS W2602

Бренд: Fisher-Price Страницы: 32

65 TREE Transplanter

Бренд: Dakota Страницы: 16

Бренд: Atlanta Страницы: 16

BOX LINER TU 70

Бренд: Krone Страницы: 92

Бренд: E-Z-GO Страницы: 114

Бренд: E-Z-GO Страницы: 134

Grizzly 700 2011

Бренд: Yamaha Страницы: 172

Бренд: Yamaha Страницы: 134

2016 Grizzly yfm700gplg

Бренд: Yamaha Страницы: 474

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 150

GRIZZLY YFM70GPAL

Бренд: Yamaha Страницы: 182

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды