Arctic Cat 1000 XT 2014 Скачать руководство пользователя страница 142

Страница: 142 / 151

140

PR715

PR717A

2. Press the piston into the caliper housing using hand

pressure only. Completely seat the piston; then wipe
off any excessive brake fluid.

PR711A

PR712

3. Apply high-temperature silicone grease (supplied

with the O-ring kit) to the inside of the caliper holder
bores and O-rings; then install the four O-rings into
the caliper.

PR719C

4. Install the caliper onto the caliper holder making sure

the caliper and holder are correctly oriented.



NOTE: It is very important to apply silicone grease

to the O-rings and caliper bores prior to assembly.

PR239C

5. Making sure brake fluid does not contact the brake

pads, compress the caliper holder toward the caliper
and install the inner brake pad; then install the outer
pad.

PR238

CAUTION

If brake pads become contaminated with brake fluid,
they must be thoroughly cleaned with brake cleaning
solvent or replaced with new pads. Failure to do so will
result in reduced braking and premature brake pad fail-
ure.

Содержание 1000 XT 2014
























































































































































Результаты поиска

Содержание 1000 XT 2014

Отзывы:

Похожие инструкции для 1000 XT 2014

Бренды по названию

Популярные бренды

Arctic Cat 1000 XT 2014, Руководство по обслуживанию

Результаты поиска

Содержание 1000 XT 2014

Отзывы:

Похожие инструкции для 1000 XT 2014

Бренды по названию

Популярные бренды