Arctic Cat 1000 XT 2014 Скачать руководство пользователя страница 75

Страница: 75 / 151

GZ454A

GZ272B

Disassembling Crankcase

Half



NOTE: For steps 1-8, refer to illustration GZ474A.

GZ474A



NOTE: To aid in installing, it is recommended the

assemblies are kept together and IN ORDER.

1. Support the right-side crankcase assembly on suitable

support blocks; then carefully remove the crankshaft
assembly (A) from the crankcase.

GZ298

2. Remove the snap ring securing the water pump drive

idler (B) to the idler shaft; then remove the drive idler.

GZ299A

3. Remove the snap ring securing the water pump idler

shaft (C) in the crankcase; then remove the shaft and
bearings.

GZ463A

4. Remove the snap ring securing the oil pump driven

gear (D) to the oil pump driveshaft; then remove the
gear. Account for a drive pin and washer.

Содержание 1000 XT 2014
























































































































































Результаты поиска

Содержание 1000 XT 2014

Отзывы:

Похожие инструкции для 1000 XT 2014

Бренды по названию

Популярные бренды

Arctic Cat 1000 XT 2014, Руководство по обслуживанию

Результаты поиска

Содержание 1000 XT 2014

Отзывы:

Похожие инструкции для 1000 XT 2014

Бренды по названию

Популярные бренды